Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
10-04-2016, 10:11 AM | #1 | |
AF Newbie
Join Date: Mar 2011
Location: Akron, Ohio
Posts: 13
Thanks: 2
Thanked 0 Times in 0 Posts
|
06 4.2. VvT soleniod
Replaced VVT soleniod on Saturday. Ordered it from Rock,Auto, I believe it is a dorman brand. I have maybe put 50 miles on it so far and the engine light is still on. Took it tomato zone and it is still reading replace VvT soleniod. How long should it take for the computer to reset?
Thank you |
|
10-04-2016, 03:45 PM | #2 | |
A990 racer
Join Date: Mar 2002
Location: Chestertown, New York
Posts: 16,946
Thanks: 25
Thanked 369 Times in 363 Posts
|
Re: 06 4.2. VvT soleniod
It could take up to 10 drive cycles, but it is possible that was not the problem, clear it see if it returns.
__________________
|
|
11-03-2016, 10:09 AM | #3 | |
AF Newbie
Thread starter
Join Date: Mar 2011
Location: Akron, Ohio
Posts: 13
Thanks: 2
Thanked 0 Times in 0 Posts
|
Re: 06 4.2. VvT soleniod
Okay VVT sensor still showing in codes, I have also replaced the crankshaft position sensor. "Took it to a shop to relearn the ignition process. It is also showing "Coolant temp, not up to regulating temp" So with that I am going to replace the Thermostat tonite. Was looking into replacing the ECT but it is in such a location on the passenger side of the block under the heat shield, that I don't know if I want to go to that point yet. Or anyone have any other ideas?I would post the codes but I am not sure where I put them at this point. After I replace the stat how many drive cycles might it take?
|
|
11-04-2016, 03:37 AM | #4 | |
AF Enthusiast
Join Date: Jul 2005
Location: the Seasonally Frozen Wastelands
Posts: 884
Thanks: 12
Thanked 58 Times in 58 Posts
|
Re: 06 4.2. VvT soleniod
__________________
. . For the good of the Free World, DEMAND COMPENSATION FROM CHINA for their release of the Virus Originating in the Wuhan Laboratory, released (intentionally or negligently) into the world in 2019 (VOWL-19). Ten trillion to start with, increasing as needed from there, PLUS compensation for the sickened, and "wrongful death" settlements for the families of those who didn't survive. END trade with Communist China. |
|
11-14-2016, 07:59 AM | #5 | |
AF Newbie
Thread starter
Join Date: Mar 2011
Location: Akron, Ohio
Posts: 13
Thanks: 2
Thanked 0 Times in 0 Posts
|
Re: 06 4.2. VvT soleniod
Replaced the thermostat took care of that issue.
Got another Dorman VVT from Rockauto. Replaced that again. Drove to work no engine light. Drove home from work(After 7 hours) no engine light. Truck sat overnight Engine light reappeared. I have replaced the VVT 2x, Crankshaft position sensor, took it to a shop to do the relearn process, they did not charge me for that ( so did they actually do it?). Should I replace the camshaft position sensor? I will be going to AutoZone tonight to have the codes read. Any other ideas? |
|
11-15-2016, 06:37 AM | #6 | |
AF Newbie
Thread starter
Join Date: Mar 2011
Location: Akron, Ohio
Posts: 13
Thanks: 2
Thanked 0 Times in 0 Posts
|
Re: 06 4.2. VvT soleniod
Still showing P0017 any ideas?
|
|
11-15-2016, 02:04 PM | #7 | |
AF Enthusiast
Join Date: Jul 2005
Location: the Seasonally Frozen Wastelands
Posts: 884
Thanks: 12
Thanked 58 Times in 58 Posts
|
Re: 06 4.2. VvT soleniod
__________________
. . For the good of the Free World, DEMAND COMPENSATION FROM CHINA for their release of the Virus Originating in the Wuhan Laboratory, released (intentionally or negligently) into the world in 2019 (VOWL-19). Ten trillion to start with, increasing as needed from there, PLUS compensation for the sickened, and "wrongful death" settlements for the families of those who didn't survive. END trade with Communist China. |
|
11-15-2016, 02:04 PM | #8 |
A990 racer
Join Date: Mar 2002
Location: Chestertown, New York
Posts: 16,946
Thanks: 25
Thanked 369 Times in 363 Posts
|
Re: 06 4.2. VvT soleniod
__________________
|
|
POST REPLY TO THIS THREAD |
Thread Tools | |
|
|