Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
10-05-2005, 06:27 PM | #1 | |
AF Newbie
Join Date: Aug 2005
Location: Hanover, Pennsylvania
Posts: 12
Thanks: 0
Thanked 0 Times in 0 Posts
|
Trany pull and new trany case...
Ok the other day I busted my tranny on a median when i was forced into it... It didnt even knock my car outta alignment but i jacked her up and took a peak at my exaust, headers... bottom of my front lip... my axel... my cv boots anything that may have been damaged.. Well nothing was damnged except a part of the trany case...
Toward the back of the car along the crack that splits the case in too and that is normaly sealed there is about 2 and a half inches where one side of it is about 1/4 an inch higher then the other resulting in a nice big open hole. So what i need to know... because its the first time i would have done this with the sol... How do i pull the trany... im looking for a pretty good tutorial that will show me the main conecters and what i have to do to make my life easy... and Im also looking for a resonably priced manual trans mission case... My del sol is a 96 Si, d16y8 enigine. |
|
10-06-2005, 03:06 AM | #2 | |
AF - Advisor
Join Date: May 2003
Location: too damn far., California
Posts: 3,039
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Trany pull and new trany case...
if you have a crack, use jb weld.
if it is a hole, get a new case or a whole tranny. to remove the tranny, remove all wires and bolts holding it. it pretty much drops out from there.
__________________
99 JRSC@9.5 psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me. |
|
10-06-2005, 11:51 AM | #3 | |
Honda GODDESS/Global Mod
|
Re: Trany pull and new trany case...
probably be cheaper/easier to just get a new tranny
|
|
10-06-2005, 07:32 PM | #4 | |
AF Newbie
Join Date: Sep 2005
Location: Bemidji, Minnesota
Posts: 82
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Trany pull and new trany case...
how hard is it to remove a tranny on a del Sol, btw? I will have to take mine out too pretty soon to put in a new clutch and flywheel.
__________________
Black 1996 del Sol VTEC Skunk 2: catback, 440g shift knob Fidanza short throw Neuspeed N2 header |
|
10-06-2005, 10:04 PM | #5 |
AF - Advisor
Join Date: May 2003
Location: too damn far., California
Posts: 3,039
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Trany pull and new trany case...
__________________
99 JRSC@9.5 psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me. |
10-07-2005, 08:41 PM | #6 | |
AF Newbie
Thread starter
Join Date: Aug 2005
Location: Hanover, Pennsylvania
Posts: 12
Thanks: 0
Thanked 0 Times in 0 Posts
|
So ill just track one down... go to my friends house one day put that bitch up on his lift drop it and swap it.
|
|
|
POST REPLY TO THIS THREAD |
|
|