Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Cadillac > Escalade | ESV | EXT
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 09-29-2014, 09:52 AM   #1
Jim Mickelson
AF Newbie
 
Join Date: Sep 2014
Location: Missoula, Montana
Posts: 4
Thanks: 1
Thanked 0 Times in 0 Posts
Question Shifter boot

2002 Escalade. Can you replace boot without cutting orange wire to controls?
Jim Mickelson is offline   Reply With Quote
Old 09-29-2014, 12:21 PM   #2
shorod
SHO No Mo
 
shorod's Avatar
 
Join Date: Jun 2004
Location: Cedar Rapids, Iowa
Posts: 10,946
Thanks: 99
Thanked 350 Times in 344 Posts
Re: Shifter boot

Assuming you're referring to the transmission shift lever on the steering column, you can remove the entire shift lever assembly by removing the steering column trim covers, the Torx screw accessed by rolling the seal on the shift lever back, and the electrical connection that is accessed once the knee bolster trim and bracket are removed.

-Rod
shorod is offline   Reply With Quote
The Following User Says Thank You to shorod For This Useful Post:
Jim Mickelson (10-01-2014)
Old 09-29-2014, 07:09 PM   #3
Jim Mickelson
AF Newbie
Thread starter
 
Join Date: Sep 2014
Location: Missoula, Montana
Posts: 4
Thanks: 1
Thanked 0 Times in 0 Posts
Re: Shifter boot

Thanks Rod,
I took the top instrument panel off and the bottom panel off; but I could not see where there was any connection. Do you need to remove the steering column bracket to access to connection? I installed the new boot over the end of the shift lever; however it tore in the process. So now I'm out $24.00 for trying.
Thank you,
Jim
Jim Mickelson is offline   Reply With Quote
Old 09-30-2014, 06:42 AM   #4
shorod
SHO No Mo
 
shorod's Avatar
 
Join Date: Jun 2004
Location: Cedar Rapids, Iowa
Posts: 10,946
Thanks: 99
Thanked 350 Times in 344 Posts
Re: Shifter boot

From what I can tell from the service manual information, as assuming you have the Tow/Haul mode with the wiring through the lever, you need to remove the upper and lower steering column shrouds then roll the boot away from the steering column to access a Torx screw. That Torx screw appears to hold the shift lever to the steering column. Once that Torx screw is removed, then you need to remove the knee bolster and plate (trim piece between the lower steering column and the brake and accel pedal, as well as the metal plate behind it) to unplug the tow/haul mode button wiring, then it appears you can remove the lever and the wiring from the steering column to install the new rubber boot.

I've not done this, I'm going off of the limited text instructions and images from the factory service manual.

-Rod
shorod is offline   Reply With Quote
Old 09-30-2014, 06:45 AM   #5
shorod
SHO No Mo
 
shorod's Avatar
 
Join Date: Jun 2004
Location: Cedar Rapids, Iowa
Posts: 10,946
Thanks: 99
Thanked 350 Times in 344 Posts
Re: Shifter boot

If you would like a PDF of the section in the service manual, send me a Private Message with the request. In the PM please include the model and year of the vehicle along with the specific request (I follow multiple models and offer diagrams quite often so it's tough for me to keep them all straight).

-Rod
shorod is offline   Reply With Quote
 
Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums .com Car Chat > Cadillac > Escalade | ESV | EXT

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 12:27 AM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts