Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
03-11-2010, 03:43 AM | #31 | |
AF Newbie
Join Date: Mar 2010
Location: Gettysburg, Pennsylvania
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to program a remote key Fob?
does any one know how to reprogram a remote key for a 1998 audi a4 quatto??? it seemed like the battery was dying cuz i would hit the lock button on the remote and it would some times work an then stopped working all together. i replaced the battery in my remote but it still wont unlock/lock my car with my remote. PLEASE HELP!
|
|
04-10-2010, 01:38 PM | #32 | |
AF Newbie
Join Date: Apr 2010
Location: Fort Madison, Iowa
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to program a remote key Fob?
This worked on my 2000 maxima
IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. 1.Close and lock all doors with the driver’s side power lock/unlock switch. 2.Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode. 3.Insert key into the ignition cylinder and turn to the ACC position. 4.Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful. 5.If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters). 6.Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. |
|
04-23-2010, 03:14 PM | #33 | |
AF Newbie
Join Date: Apr 2010
Location: Graham, Washington
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to program a remote key Fob?
Thanks for the great info!
I was able to reprogram my remote in one try! My husband thinks I'm a genius! |
|
12-23-2011, 11:45 AM | #34 | |
AF Newbie
Join Date: Dec 2011
Location: Miamisburg, Ohio
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to program a remote key Fob?
I have a 2010 Nissan Altima and a pocket full of keys plus a fob for starting/entering vehical/etc.
Could I buy a key with a embedded transponder that could be programmed to allow me the same results and give me some room in my pocket again?? Thanks for any help provided... |
|
01-04-2012, 10:47 AM | #35 | |
AF Newbie
Join Date: Dec 2011
Location: Miamisburg, Ohio
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to program a remote key Fob?
carl.odle
1-4-2012, 11:50 AM I have a 2010 Nissan Altima and a pocket full of keys plus a fob for starting/entering vehical/etc. Could I buy a key with a embedded transponder that could be programmed to allow me the same results and give me some room in my pocket again?? Thanks for any help provided... |
|
03-09-2012, 11:23 PM | #36 | |
AF Newbie
Join Date: Mar 2012
Location: montreal
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to program a remote key Fob?
Hi, i have a nissan versa 2007 model S 1.8 hatchback. I bought it used and it came with remote control. The remote works only to start the car. The lock and unlock button does not work it only makes the lights flash on the car... i tryed to program the remote as mentionned in this forum but it does not seem to enter programming mode. The car is basic no power lock. To get in the trunk i have to unlock my front door, anyways can i program this type of car model? Or else what can i do? Thanks for any help
|
|
05-21-2012, 01:19 AM | #37 | |
AF Newbie
Join Date: May 2012
Location: Vancouver
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to program a remote key Fob?
Hi Yannick, you can find instructions to program the remote for your Versa on the site http://programcarremotes.com
I think the link to your particular model is 2009 Nissan Versa Let me know if that works or not and I will try to dig up something else that works. |
|
08-01-2012, 08:08 PM | #38 | |
Authorized Vendor
Join Date: Sep 2003
Location: Keyless Entry Remotes
Posts: 741
Thanks: 0
Thanked 8 Times in 8 Posts
|
Re: How to program a remote key Fob?
Do you have the base remote or smart key remote for your Versa as shown here?
http://originalkeyless.com/searchqui...%2207+Versa%22
__________________
Replacement keyless entry remotes available here - up to 90% off - All makes/models from Acura-Volvo, 1988-present - http://www.OriginalKeyless.com |
|
11-10-2013, 11:59 AM | #39 | |
AF Newbie
Join Date: Nov 2013
Location: Sydney
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to program a remote key Fob?
Hi
You can program yourself. Just follow simple instructions. http://programkeyfob.com/nissan/nissan.html |
|
|
POST REPLY TO THIS THREAD |
Thread Tools | |
|
|