 |
 |
 |
|
|
 |
| Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
 | | ||
| |
|
| Latest | 0 Rplys |
02-28-2008, 07:06 PM
|
#1 | |
|
AF Newbie
Join Date: Feb 2008
Location: Charlotte, North Carolina
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
0171,0174 codes
I'm getting trouble codes 0171,0174 bank1 and bank2 too lean. I just did a complete tune-up on it and also pulled the trottle body and cleaned the EGR
ports to clear the 04901 code. This worked!!! I also went ahead and changed the EGR valve, EGR sensor,and the EGR solenoid for good measure. I can't figure why now im getting the bank1,2 codes. Anyone had this same problem? |
|
|
|
|
02-29-2008, 05:09 AM
|
#2 | |
|
AF Ford Contour-Advisor
 
Join Date: Mar 2003
Posts: 1,815
Thanks: 0
Thanked 2 Times in 2 Posts
|
Re: 0171,0174 codes
Youve got a vacuum leak now. I'd check around the TB first.
You did buy new TB and EGR gaskets right?
__________________
 "The CEG Nazi" www.contour.org 1996 Ford Contour SE - Sold 3.0L V6 and Arizona Dyno Chip Turbo Kit 364 whp, 410 wtq @ 16 psi and only 4,700 rpms. 1999 Tropic Green SVT Contour - Bone stock and MINT |
|
|
|
|
|
03-03-2008, 08:06 AM
|
#3 | |
|
AF Newbie
Thread starter
Join Date: Feb 2008
Location: Charlotte, North Carolina
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 0171,0174 codes
I didn't buy a new TB but I did get a new EGR gasket. I did how ever find a posible vacum leak were the main vacum line plugs into the pcv valve. The conector that locks the vacum line to the valve is broken and I can pull it loose. The good thing is that it also tells me that the PCV valve is good because when i pull it loose the engine idle changes. I could here it sucking air when my bro. reved the engine. I'm going to see if I can find a new vacum line for it. I'm sure i'll need to get it from the dealer because I can't find it on autozone's web site or advance auto's web site.
|
|
|
|
|
|
01-29-2011, 09:05 AM
|
#4 | |
|
AF Newbie
Join Date: Jan 2011
Location: Apex, North Carolina
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 0171,0174 codes
I had this same problem and went to 3 diffrent shops (because I could not figure it out). Finaly I was told it was and replace the lower intake manifold. The rods that support the seconday butterflies have some sort of seal. The seal went bad. I could not find any one to rebuild it or could I find the parts to rebuild it. Good luck
|
|
|
|
|
|
01-29-2011, 07:32 PM
|
#5 | |
|
AF Enthusiast
Join Date: Mar 2008
Location: garner, North Carolina
Posts: 3,579
Thanks: 86
Thanked 100 Times in 100 Posts
|
Re: 0171,0174 codes
A Smoke test would of pinpointed this leak!
Some shops, like to take a little problem, and turn it into a Major project @ the customers expense. |
|
|
|
|
|
01-29-2011, 08:27 PM
|
#6 | ||
|
AF Ford Contour-Advisor
Join Date: Mar 2003
Posts: 1,815
Thanks: 0
Thanked 2 Times in 2 Posts
|
Re: 0171,0174 codes
Quote:
__________________
"The CEG Nazi" www.contour.org 1996 Ford Contour SE - Sold 3.0L V6 and Arizona Dyno Chip Turbo Kit 364 whp, 410 wtq @ 16 psi and only 4,700 rpms. 1999 Tropic Green SVT Contour - Bone stock and MINT |
||
|
|
|
|
 |
POST REPLY TO THIS THREAD |
 |
| Thread Tools | |
|
|
