 |
 |
 |
|
|
 |
| Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
 | | ||
| |
|
| Latest | 0 Rplys |
|
|||||||
| View Poll Results: k26 or S16G? | |||
| K26 |
   
|
0 | 0% |
| S16G |
  
|
2 | 100.00% |
| Voters: 2. You may not vote on this poll | |||
 |
 Show Printable Version |  Email this Page | 
Subscribe to this Thread
|
|
|
Thread Tools |
07-26-2007, 05:14 AM
|
#1 | |
|
AF Enthusiast
 Join Date: Sep 2004
Location: vancouver, Washington
Posts: 2,886
Thanks: 0
Thanked 0 Times in 0 Posts
|
K26 vs S16G???
Ok, i have a REALLY good condition K26, that i was going to run. But i have a new S16G from forcedperformance also. The thing is, i need money, and was going to sell off my S16G and put this K26 i had on. The only thing is, i think this would be a downgrade in performance. The k26 looks bigger, but the wheel is smaller, and from what i can tell the S16G is outflowing the K26 on the flow chart. Im not an expert, and flow charts are difficult, but it seems like they have similar flow on the bottom end but as the pressure ratio increases the K26 starts losing effeciency? Take a look and tell me what you think....
S16G flow chart..... http://www.rbracing-rsr.com/turbo/Tu...5-16glarge.gif K26 flow chart http://www.rbracing-rsr.com/turbo/TurboMaps/k26_map.jpg Heres the K26 next to the S16G  What do you guys think?
__________________
1988 conquest TSI -Lots of mods, finally finished WOOT!!  Horsepower sells cars, Torque wins races! |
|
|
|
|
07-26-2007, 06:06 PM
|
#2 | |
|
AF Enthusiast
 Join Date: Aug 2003
Location: sunny, California
Posts: 1,988
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: K26 vs S16G???
u have a BROKEN turbo on the left side my brother...
look at the fins.
__________________
"A good driver is measured not by his lap times, but by the amount of time he spend trying to make sense of his car" E.K. |
|
|
|
|
|
07-26-2007, 06:07 PM
|
#3 | |
|
AF Enthusiast
Join Date: Sep 2004
Location: vancouver, Washington
Posts: 2,886
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: K26 vs S16G???
i know, a couple of the fins are fucked up on the edges, whatdaya do though? I think i might just buy a new wheel, and keep my S16G
__________________
1988 conquest TSI -Lots of mods, finally finished WOOT!! Horsepower sells cars, Torque wins races! |
|
|
|
|
|
07-26-2007, 06:39 PM
|
#4 | |
|
AF Enthusiast
Join Date: Aug 2003
Location: sunny, California
Posts: 1,988
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: K26 vs S16G???
KKK is a better company then MITSU. KKK makes the turbos for HKS.
because of the size, u will have lag dough.
__________________
"A good driver is measured not by his lap times, but by the amount of time he spend trying to make sense of his car" E.K. |
|
|
|
|
|
07-27-2007, 01:17 AM
|
#5 | |
|
AF Enthusiast
Join Date: Sep 2004
Location: vancouver, Washington
Posts: 2,886
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: K26 vs S16G???
yeah i know, it lags about 3300rpm will build 14psi. Its not bad though, i think the KKK will rip on the freeway. Im going to put a new wheel in my S16G, sell it, and do a tial/k26 combo.
__________________
1988 conquest TSI -Lots of mods, finally finished WOOT!! Horsepower sells cars, Torque wins races! |
|
|
|
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
