Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Toyota > IS200/IS300/IS350/Altezza
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 02-26-2005, 09:32 AM   #1
Matt_IS300
AF Newbie
 
Join Date: Feb 2005
Location: raleigh, North Carolina
Posts: 17
Thanks: 0
Thanked 0 Times in 0 Posts
Transponder Key programming instructions?

I've ordered a 2nd masterkey off of eBay but the instructions I downloaded off of the internet don't seem to work. I'm getting frustrated w/ the whole deal because I had lots of problems getting the key cut in the first place because my used 2001 IS 300 had the ignition switch changed so it has a new key code different from the original one that's matched to the VIN. Either way, the key opens the door and is cut right but I cannot get the thing programmed. HELP!!!

Matt
Matt_IS300 is offline   Reply With Quote
Old 08-23-2005, 11:05 PM   #2
Brian R.
Resident Chemist
 
Brian R.'s Avatar
 
Join Date: Feb 2004
Location: Rockville, Maryland
Posts: 8,586
Thanks: 105
Thanked 157 Times in 157 Posts
Send a message via Yahoo to Brian R.
Re: Transponder Key programming instructions?

For 1998+ Toyota, Lexus
Add Duplicate Key
1. Simultaneously depress and release brake and accelerator pedals 1 time.
2. Insert existing master key into ignition.
3. Within 15 seconds depress and release accelerator pedal 5 times.
4. Within 20 seconds depress and release the brake pedal 6 times and
remove key.
5. Within 10 seconds insert new key into ignition.
6. Within 10 seconds depress and release the accelerator pedal 1 time.
7. After 80 seconds new key is registered and security light goes off.
8. Remove new key and depress and release brake pedal 1 time.

For 2002+ Toyota, Lexus
Add Duplicate Key
Requires one working Toyota/Lexus Master Key.
1. Make sure all doors and windows are closed.
2. Insert Master key into the ignition cylinder.
3. Cycle the ignition cylinder from On to OFF five times.
4. Open and close the “driver side” door 6 times.
5. Remove the Master Key and insert the new duplicates key.
6. TURN THE IGNITION CYLINDER ON.
7. The new key will be registered after 60 seconds. The THEFT light on the dashboard will go out, indicating that programming has been completed.

http://www.kaba-ilco.com/key_systems...16-E-0205].pdf
__________________
Forum Guidelines:http://www.automotiveforums.com/vbulletin/guidelines.html

"What we've got here is a failure to communicate"
Brian R. is offline   Reply With Quote
The Following User Says Thank You to Brian R. For This Useful Post:
sallupat (03-21-2011)
Old 03-17-2007, 03:18 AM   #3
Chuckfw
AF Newbie
 
Chuckfw's Avatar
 
Join Date: Mar 2007
Location: Willow Park, Texas
Posts: 34
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Transponder Key programming instructions?

To program the remotes on your new key, you have to go through the door lock exercise using the old programmed key. I spent a lot of time trying to program using the new key and found out that the old key needs to be used when you do the door lock/unlock routine.
Chuckfw is offline   Reply With Quote
Old 10-03-2007, 12:59 PM   #4
zuzuzu
AF Newbie
 
Join Date: Oct 2007
Location: Galway
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Transponder Key programming instructions?

hey folks...

does this work with a normal key is which the battery has died?
i have a normal key and the battery died and i replaced the battery but the lock unlock function will not work on the key. i can start the car with the key. its a 03 7th gen celica i own. any ideas?
zuzuzu is offline   Reply With Quote
Old 02-19-2010, 05:39 PM   #5
cdelcam
AF Newbie
 
Join Date: Feb 2010
Location: houston, Texas
Posts: 1
Thanks: 0
Thanked 1 Time in 1 Post
Re: Transponder Key programming instructions?

I was successful over the weekend programming a new key for a 2002 Lexus ES300 using the "pedal dance" method. The "door" method did not work. Also, to program the remote, FCC ID#HYQ1512V, the correct method is to do the following with the new key:
1.with no key in the ignition an dthe drivers door open and unlocked
2.within 4-5 seconds put the key in the ignition and remove 2 times
3.close the drivers door and open 2 times
4.put the key in the ignition and remove
5.close the drivers door and open 2 times
6.put the key in the ignition and close the drivers door
7.turn the ignition to ON for 1 second then turn OFF
8.remove the key from the ignition
9.the power locks should now cycle once
10.press the unlock and lock buttons at the same time for 1 second and then quickly press the unlock and lock buttons for 1 second again
11.if the remote is programmed the door locks will cycle once. If failed the door locks will cycle 2 times
12.open the drivers door to end the procedure!

After trying all the other procedures I found, like power lock switch 5 times, or manual door lock switch 5 times, etc....I found the procedure listed above and it is correct. I programmed the new remote in under 5 minutes!....good luck!
cdelcam is offline   Reply With Quote
The Following User Says Thank You to cdelcam For This Useful Post:
sallupat (03-21-2011)
 
Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums .com Car Chat > Toyota > IS200/IS300/IS350/Altezza

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 01:47 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts