Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Fiberglassing Fiberglasssing explained and the proper techniques on working on a fiberglass project. |
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
07-28-2004, 08:40 PM | #1 | |
Grande Boleros de Fuego
Join Date: Jan 2004
Location: Denver, Colorado
Posts: 7,719
Thanks: 0
Thanked 3 Times in 2 Posts
|
Gonna need some fiberglass help soon...
I want to make a custom enclosure for my subs in my trunk. I have two twelves, and want to make something like:
Not quite that far apart though, but it gets the idea across. And I would want the amp behind the enclosure. And if you cant tell in that drawing, both are kind of angled inward. Only problem is, I have no idea where to start. Anyone got any resources or tutorials you could link me too? Or wanna to take the time to write one? Or just any tips on where to start? Thanks, Tim
__________________
MAKE ART, NOT WAR |
|
07-28-2004, 09:01 PM | #2 | |
Captain Over Engineer
|
Re: Gonna need some fiberglass help soon...
I'll help you out man. I do it the classic way, and avoid the kitty hair.
First you need some polyurethane foam, it can be expensive, so I have a reccomendation. Go to a commercial construction site, and look for some yellow somewhat "hard" foam. To see if it will work, mix up some bondo or epoxy and put it on it, let it cure. Thats the test, and 95% of the time it will work when laying the fiberglass. Get a bunch of the blocks, take off the backings so its pure foam. Glue them together with bondo until you get a rectangular box the size that you need to carve out of. Take a sawzall or resiprocating saw and cut out the basic shape. After the basic shape has been formed, start sanding it into a better shape. After the shape is formed cut out the holes for the subs. Try to find some wood circles if you can to place in the holes to insure a perfect fit for your subs. Now the fun part, mix the fiberglass with the epoxy. I can go through that if you need. And drape it over the foam mold. After it starts to kick (get hard) cut out the circles with a sharp razor. If it starts to pull, let it cure a little more. Then repeat about 5-8 times, depending on the strength. Theres the basics.
__________________
-Mike AF Director of Media / Photographer mike.lawrence@automotiveforums.com | AutomotiveForums.com | Flickr Gallery |
|
07-29-2004, 01:40 AM | #3 | |
AF Fanatic
|
That's pretty much the way it's done... You can get insulating foam from a hardware store, Home Depot should have it in big 4x8 sheets. Get a can or two of 3M spray adhesive, and give it a good liberal coating to glue the sheets together in a stack as needed. The easiest way to get a good rough cut to start with is using a snapoff blade style utility knife, and then working with a coarse grit sandpaper to smooth it out. Getting some of the contours right can be really tricky, especially when you have to make two of them identical.
You'll want to get a block of wood for sanding, a chunk of 1" dowel can be really handy too, and I've used a large softball before to get a nice rounded shape for sanding. It often helps to cut slits in the edges of the sandpaper to get it to fold nicely around the ball. Don't be afraid to slather more resin on, it'll give you more surface you can sand down, and a lot more margin for error.
__________________
Connor - Porsche Nazi since 2001, VW defiler since 2004 This here's a Fabrication forum! My lugnut requires more torque than your LS1 makes. |
|
07-29-2004, 02:07 AM | #4 | |
Grande Boleros de Fuego
Thread starter
Join Date: Jan 2004
Location: Denver, Colorado
Posts: 7,719
Thanks: 0
Thanked 3 Times in 2 Posts
|
Re: Gonna need some fiberglass help soon...
Is the foam the easiest way to go? Because I have seen a couple in progress projects on various site where the guy has has built a wooden frame and streteched fabric over it.
__________________
MAKE ART, NOT WAR |
|
07-29-2004, 06:49 AM | #5 | |||
Captain Over Engineer
|
Re: Gonna need some fiberglass help soon...
Quote:
Quote:
__________________
-Mike AF Director of Media / Photographer mike.lawrence@automotiveforums.com | AutomotiveForums.com | Flickr Gallery |
|||
07-29-2004, 10:00 AM | #6 | ||
Grande Boleros de Fuego
Thread starter
Join Date: Jan 2004
Location: Denver, Colorado
Posts: 7,719
Thanks: 0
Thanked 3 Times in 2 Posts
|
Re: Re: Gonna need some fiberglass help soon...
Quote:
__________________
MAKE ART, NOT WAR |
||
07-29-2004, 02:06 PM | #7 | |
Captain Over Engineer
|
Re: Gonna need some fiberglass help soon...
I'll explain later Tim, I'm off to work.
__________________
-Mike AF Director of Media / Photographer mike.lawrence@automotiveforums.com | AutomotiveForums.com | Flickr Gallery |
|
07-29-2004, 02:27 PM | #8 | |
AF Fanatic
|
Actually, polystyrene is fairly resistant when it comes to heat, unless you're casting a boat hull or something with many weaves of fibre. As long as you coat it with something, it should would out. A friend of mine uses this method, and gives it a spray coat of an acryllic enamel to seal it and make the mold.
__________________
Connor - Porsche Nazi since 2001, VW defiler since 2004 This here's a Fabrication forum! My lugnut requires more torque than your LS1 makes. |
|
08-03-2004, 05:50 PM | #9 | |
AF Enthusiast
|
I was going to suggest fabbing the wooden box and stretching the material since its your first time(although I've never done it). From what I've seen, it looks just as great while saving time and money. You will also be more likely to match the speaker enclosure.
|
|
08-11-2004, 05:59 PM | #10 | |
Forunn Daberator
Join Date: Mar 2004
Location: bumblefuck, Texas
Posts: 10,590
Thanks: 363
Thanked 364 Times in 309 Posts
|
Re: Gonna need some fiberglass help soon...
Build the back of your box with MDF, out out rings for your subs out of MDF, this is just what it sounds like, a ring that your sub fits into and is about 1" wide from inside circle to outside circle. Use scrap peices of wood or what ever and position the rings where you want them, hot glue them in place with scrap peices of wood. Use Fleece to stretch over and stapple to the sides of the box and to the rings. Coat it in fiberglass resin and let dry. Now build up using fiberglass mat about 1/2- 3/4" thick. Dont fiberglass the fleece on the insides of the ring. Use a knife to cut out the fleece on the insides of the rings. Now sand it with an electric sander and smooth with bondo, final sanding by hand. This is alot easyer than trying to do it with foam.
__________________
|
|
08-16-2004, 02:52 PM | #11 | |
AF Enthusiast
|
Re: Gonna need some fiberglass help soon...
check out www.the12volt.com as well. it's a plethora of knowledge about fiberglassing as well.
i'm wanting to do my own sub box also and have been researching for about 2 months now. |
|
10-17-2006, 01:17 AM | #12 | |
AF Newbie
Join Date: Oct 2006
Location: napoleon, Ohio
Posts: 11
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Gonna need some fiberglass help soon...
I am in the process of starting a custom composite fabrication shop , I have built many show winning cars that have had completly fiberglassed interiors, plus we specalize in fabrication of custom fiberglass enclosures, as well as custom body parts. all parts can be wraped in vinyl, carpet, or can be layed up in carbon fiber, or platnum carbon fiber (aluminized) or can be painted.. I would be interested in discussing what you want in more detail so that an accurate price can be established.. feel free to email me for more information..I have pictures of previous work that i have done that i can email to you at your decression..
|
|
01-10-2007, 10:42 PM | #13 | |
AF Newbie
Join Date: May 2006
Location: Buffalo, New York
Posts: 82
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Gonna need some fiberglass help soon...
O.K., the audio guy's pissing me off. spam somewhere else, asshole.
__________________
The Builder |
|
|
POST REPLY TO THIS THREAD |
|
|