Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Automotive Art > Car Modeling > WIP - Street
WIP - Street Post topics for any "Works In Progress" street vehicles projects in this sub-forum.
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools Search this Thread
Old 02-09-2019, 04:56 PM   #196
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

The steering shaft was threaded through the header and into the rack & pinion. Then the scratch-built dash was installed.
Scale-Master is offline   Reply With Quote
Old 02-10-2019, 05:11 PM   #197
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

The beginning of the spare tire hold down. PE frame and milled resin handle; brass hinge pin.

Scale-Master is offline   Reply With Quote
Old 02-11-2019, 12:13 PM   #198
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

The headlights have been installed and wired. I made bulbs for the parking lights too. Radiator is installed. More electrical wiring getting done…
Scale-Master is offline   Reply With Quote
Old 02-11-2019, 06:54 PM   #199
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

We have ignition, wires… They will be routed properly after the carbs are installed.
Also added the ground point for the battery, the clutch hydraulic line and some more oil lines.
Scale-Master is offline   Reply With Quote
Old 02-21-2019, 05:57 PM   #200
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

Been working on the Weber carbs. Adding the linkages and more hardware. Even made the tiny screws to sync the carbs.


Scale-Master is offline   Reply With Quote
Old 02-22-2019, 12:10 PM   #201
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

Throttle cable guide with mounting bracket. Aluminum and stainless steel.
Scale-Master is offline   Reply With Quote
Old 02-22-2019, 03:42 PM   #202
360spider
AF Moderator
 
360spider's Avatar
 
Join Date: Sep 2002
Location: Fort Worth, Texas
Posts: 2,713
Thanks: 12
Thanked 204 Times in 136 Posts
Re: LHD Seven

Holy smokes. Outstanding updates. The plate is out of this world!
__________________
The client is not always right. - Enzo Ferrari
ItalianHorses.net
360spider is offline   Reply With Quote
Old 02-22-2019, 06:43 PM   #203
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

Thanks Spider! It is a fun project...

Got the cable and linkage installed. Still need to wind the return spring.
Scale-Master is offline   Reply With Quote
Old 02-23-2019, 01:53 PM   #204
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

I made and installed the throttle return springs; should be two because one is not safe.
Made and added the lettering to the plug wires too.

Also finished plumbing the rear brake lines.
Scale-Master is offline   Reply With Quote
Old 02-23-2019, 08:17 PM   #205
jeffmorris
AF Newbie
 
Join Date: Sep 2003
Posts: 40
Thanks: 0
Thanked 0 Times in 0 Posts
Re: LHD Seven

Do you have rear license plate holder? Mine broke.
jeffmorris is offline   Reply With Quote
Old 02-24-2019, 10:34 AM   #206
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

That's normally part of the frame. I modified this one so it can be removed with the spare. If I were in you r position I would make a new one from brass and/or plastic.
Scale-Master is offline   Reply With Quote
Old 02-25-2019, 03:44 PM   #207
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

The tops of the carbs have been installed and the fuel fittings were machined/fabricated and attached to them. A section of the fuel line is on too.
It's starting to get tight between the carbs. But there is enough clearance for the linkages to work without rubbing the wires.

Scale-Master is offline   Reply With Quote
Old 02-27-2019, 11:47 AM   #208
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

Fuel pressure regulator. Because it's mandatory for Webers… Machined aluminum.
Scale-Master is offline   Reply With Quote
Old 02-28-2019, 03:25 PM   #209
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

Added the decals and installed the regulator into the fuel line.
Scale-Master is offline   Reply With Quote
Old 02-28-2019, 09:32 PM   #210
Scale-Master
AF Enthusiast
Thread starter
 
Scale-Master's Avatar
 
Join Date: Oct 2004
Location: H.B., California
Posts: 2,662
Thanks: 4
Thanked 26 Times in 25 Posts
Re: LHD Seven

Not cast; individually machined from resin. Air filters…
Scale-Master is offline   Reply With Quote
 
Reply

POST REPLY TO THIS THREAD


Bookmarks
Go Back   Automotive Forums .com Car Chat > Automotive Art > Car Modeling > WIP - Street

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 07:30 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts