altezza wiring diagram (3S-GE Beams)

carina_rwd · 02-02-2004, 12:10 PM

I´m looking for wiring diagram to rs200 altezza, 3S-GE beams with manual transmission.
Any ideas where to get one?

kari

matada · 02-02-2004, 08:32 PM

do you need the entire diagram? I have bits and pieces here, so if you are looking for something detailed I can probably help out (like the ecu plug description etc.)

carina_rwd · 02-03-2004, 02:09 PM

everything helps I think. I´m putting that kinda engine into a old carina, I have altezza frontcut and all wires and boxes are there. But I think there are lots of extra and unwanted stuff also. So espesially all wires etc. which are directly connected to engine management are most needed.

thanks
kari

carina_rwd · 02-15-2004, 03:42 PM

is this forum dead or something

please, someone! I need help to get that wiring diagram. Beams 3S-GE sits nicely in old skool carina and even that 6-speed trans fit perfectly, but it would be nice to drive it also.

kari

carina_rwd · 02-21-2004, 02:31 PM

I´ve sorted out quite much of those wires, but I really need ECU pins/connectors "chart" any ideas were to get some help?

chengkhang · 03-02-2004, 11:45 AM

yes is this thread dead?????

i am also looking for altezza wiring diagram (3S-GE dual Beams vvti)

no luck yet.....
i am putting it into my 93 mr2...its in it already... i just need too figure out the wiring... hopfully i finish it this year.....

help any one....

carina_rwd · 03-03-2004, 03:13 PM

toysport(.com) in usa can seek those wirings and translate those to english, it will take about 2-3 weeks and costs $100.

it might be the only way to get our beams run again

Silo · 06-29-2004, 05:21 PM

chengkhang, you have installed the black top Altezza 3S-GE in your 93 MR2? Do the engine mounts match or did you have to make custom ones?

Did you get the wiring diagram yet?

TRD2000 · 08-01-2004, 08:49 PM

How Much Different Is The Altezza Wiring Loom? I'm Looking At Putting One In My Mr2 But I'm Wondering If I Can Use The Same Computer For My 3sgte Until I Do The Swap? I Know The Program Would Be Different But Can I Do It Phisically?

chengkhang · 11-17-2004, 01:05 AM

Quote:

Originally Posted by Silo

chengkhang, you have installed the black top Altezza 3S-GE in your 93 MR2? Do the engine mounts match or did you have to make custom ones?

Did you get the wiring diagram yet?

yes i have it installed... the altezza 3sge is the same block as the mr2 turbo soo it bolted up prefect with the tranny, remeber 3 of 4 mounts are mounted on the tranny, oh yeah it bolts on to the stock mr2 tranny to,... so yeap it fits prefect,.. no custom if you did it like how i did it,... which i am trying to do the least not need custom work,....

oh took pictures,... i gota see if i still have them,.....

chengkhang · 11-17-2004, 01:11 AM

Quote:

Originally Posted by TRD2000

How Much Different Is The Altezza Wiring Loom? I'm Looking At Putting One In My Mr2 But I'm Wondering If I Can Use The Same Computer For My 3sgte Until I Do The Swap? I Know The Program Would Be Different But Can I Do It Phisically?

theres a whole lot of different thats why im looking for help,. on harness work and looking for diagrams,..... i dont think you would want to use the 3sgte ecu total different,.... altezza 3sge has dual-vvti,...... you can modify the motor but whats the point of getting that motor for if you dont want vvti,... unless you just want the aluminum block,...??????? thats coool tooo

TRD2000 · 11-17-2004, 12:44 PM

i didn't realise it had an alloy block! I want to turbo it so perhaps i should look at using my iron block and the altezza head? decided to use a motec ecu.

chengkhang · 11-18-2004, 12:51 AM

Quote:

Originally Posted by TRD2000

i didn't realise it had an alloy block! I want to turbo it so perhaps i should look at using my iron block and the altezza head? decided to use a motec ecu.

what would be cool if you can re-sleeve with titaium sleeves, the alloy block like hondas, now that would be tight,.... and then turbo,.....

TRD2000 · 11-18-2004, 12:37 PM

yeah... that would definately be cool. doesn't honda use a an CRM compound for their sleeves as standard? well on the NSX.

do you think the 4th gen BEAMS head will bolt to an older gen block?

chengkhang · 11-20-2004, 03:43 PM

Quote:

Originally Posted by TRD2000

yeah... that would definately be cool. doesn't honda use a an CRM compound for their sleeves as standard? well on the NSX.

do you think the 4th gen BEAMS head will bolt to an older gen block?

ummm i donw know i havent taken the head my beams yet, but i would think so,.. lets just hope,...... its is still the 3s block

POST REPLY TO THIS THREAD