Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
11-27-2010, 07:38 PM | #1 | |
AF Newbie
Join Date: Jan 2009
Location: Taylor, Michigan
Posts: 9
Thanks: 0
Thanked 0 Times in 0 Posts
|
97 Jimmy4.3L extreme engine vibration, random misfire code
I was traveling home from a weekend of hunting when I noticed a decrease in power, an rpm increase of 200 to maintain same speed and my ses light went from solid on, to blinking. When I pulled over I could barely keep it running, and when I did turn it off it "dieseled" or continued to run. When I finally made it back home and to an Autozone to check the engine code it gave me Random misfire condition. It has 165000 miles on it, so I figured I'd do a compression check, getting nothing on one cylinder? I have seen a lot of posts about CPI, ignition system problems, they seemed like a minor misfire compared to what I was seeing. The engine vibration was terrible.
|
|
11-28-2010, 08:59 PM | #2 | |
Advisor/Moderator
Join Date: Nov 2005
Location: Belleville, Michigan
Posts: 5,184
Thanks: 6
Thanked 103 Times in 95 Posts
|
Re: 97 Jimmy4.3L extreme engine vibration, random misfire code
P0300 along with a blinking SES light is almost ALWAYS caused by faults in the secondary ignition system: Spark plugs, plug wires, distributor cap, distributor rotor, ignition coil, and ignition module. These engines are very fussy when it comes to replacing them so don't cut corners trying to save money. Start with a set of AC Delco plugs, and an AC Delco distributor cap, and rotor. Put a dab of silicone dielectric grease on each terminal of the cap, inside and out. Use Autolite Professional Series wires, they're cheaper and better than AC Delco wires Next step is check fuel pressure and leakdown. Key ON, engine OFF, fuel pump running: pressure must be 60psi to 66psi and must remain above 55psi for 3 to 5 minutes after the pump shuts off. Post your results.
__________________
You have to know how it works, to figure out why it doesn't. |
|
12-02-2010, 06:43 AM | #3 | |
AF Newbie
Join Date: Nov 2010
Location: Candiac
Posts: 30
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 97 Jimmy4.3L extreme engine vibration, random misfire code
If he is getting "0" compression on 1 cylinder, I would start there. No amount of plugs or wires is going to revive a dead cylinder. It is time for a leak test on that cylinder. Could be a hole in the piston, rings, valves....
Don |
|
12-05-2010, 09:03 PM | #4 | |
AF Newbie
Join Date: Aug 2010
Location: Mount Vernon, Illinois
Posts: 55
Thanks: 2
Thanked 1 Time in 1 Post
|
Re: 97 Jimmy4.3L extreme engine vibration, random misfire code
Think it might have bent a pushrod?
__________________
'83 Pontiac Bonneville 361 SBC .150 domes 3.500" Sprint car crank Comp 260 H 3.73:1 behind 700 R4 Jensen tape deck & 6X9's |
|
12-11-2010, 08:26 AM | #5 | |
AF Newbie
Join Date: Nov 2010
Location: Candiac
Posts: 30
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 97 Jimmy4.3L extreme engine vibration, random misfire code
I don't know why you would suspect a bent pushrod. I would think you would have heard a mechanical noise when you were coming back from your trip. It is true that, if the valves don't open,you will not get any compression on that cylinder. I would still start with a leak test and if you don't find anything out of the ordinary, I would investigate further (Spark & gas) before pulling the head, unless you have good reason to suspect a bent pushrod. Take this advice with a grain of salt as I am not a pro mechanic but rather a DIY wrench!
Don |
|
01-19-2011, 12:55 AM | #6 | |
AF Newbie
Join Date: Nov 2010
Location: clifton, New Jersey
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 97 Jimmy4.3L extreme engine vibration, random misfire code
fuel injectors maybe.?. or a sensor
|
|
11-28-2018, 07:12 PM | #7 | |
AF Newbie
Join Date: Oct 2018
Location: Pine bluff, Arkansas
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 97 Jimmy4.3L extreme engine vibration, random misfire code
Been there, done that.. Bet its a stuck valve
|
|
11-28-2018, 10:13 PM | #8 | |
AF Fanatic
Join Date: Jul 2011
Location: Worcester, Massachusetts
Posts: 5,017
Thanks: 70
Thanked 618 Times in 610 Posts
|
Re: 97 Jimmy4.3L extreme engine vibration, random misfire code
Newbie, check the date of the last post...
|
|
11-29-2018, 09:35 PM | #9 |
AF Newbie
Join Date: Oct 2018
Location: Pine bluff, Arkansas
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 97 Jimmy4.3L extreme engine vibration, random misfire code
|
|
POST REPLY TO THIS THREAD |
Thread Tools | |
|
|