Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Engineering/Technical Ask technical questions about cars. Do you know how a car engine works? |
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
07-15-2001, 10:41 PM | #1 | |
AF Newbie
Join Date: Jul 2001
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
New Tangential Engine Design
I have designed a new engine, it is a tangential design, it reduces mechanical friction losses by one quarter, saving petrol by a quarter. I have had a car running on with this engine for 37 years. Please go and see my site and get back to me with what you think.
www.geocities.com/tangentialengine Please email me with any of your thoughts or queries. Jack |
|
07-17-2001, 10:41 PM | #2 | |
Volvo Guy
|
I read your site, and I sent you a e-mail.
__________________
-Joe- '02 Volvo S60 T5 Sold!1993 volvo 850 Intake, Exhaust, Springs, Shock, I.C.E. |
|
07-20-2001, 08:02 PM | #3 | |
AF Enthusiast
Join Date: May 2001
Location: Ramstein AB
Posts: 1,240
Thanks: 0
Thanked 1 Time in 1 Post
|
It seems that an engine such as this might take up some more space in the engine bay and add to weight. Right now, automakers can stay under government set emissions with other forms of technology. However, it does seem like a great design for the future, when pollution standards become stricter.
|
|
07-20-2001, 08:14 PM | #4 | |
AF Regular
Join Date: Mar 2001
Posts: 184
Thanks: 0
Thanked 0 Times in 0 Posts
|
Jack, it seems like a good design. Would that design not put even more friction on the cylinder wall on the upstroke? I'm not an engineer or anything, but that makes sense to me. Have you approached any automakers?
__________________
[000000] I-6 Power |
|
08-01-2001, 05:01 PM | #5 | |||
Pretty much amazing
|
I'm Lost can somebody explain more?
__________________
ec437 on grammar; Quote:
Quote:
|
|||
08-01-2001, 06:59 PM | #6 | |
AF Enthusiast
Join Date: May 2001
Location: Ramstein AB
Posts: 1,240
Thanks: 0
Thanked 1 Time in 1 Post
|
In many mechanical devices, friction is the cause for reduced performance and general wear down, and it must be minimized as much as possible (sometimes friction is openly welcomed, such as the connection between a tire and the ground). It prevents moving parts from reaching maximum potential. Parts rub against each other, thereby converting kintetic energy into heat energy.
In a modern internal combustion engine's cylinder, a piston is sent downwards by the fuel/O2/ignition burn, which forces the attached connecting rod below to turn the crankshaft. Since the crankshaft is directly below the piston, the ignition must occur right when the rod/crank point has just passed top dead-center on its way back down in order to keep the crankshaft moving. The only problem is that the position of the rod at this time is at an angle, and causes the piston to press against one side of the cylinder wall. This pressure slows down the piston's downward movement and power is lost, while unwanted excess heat is built. The tangential engine addresses this natural flaw by having the crankshaft offset to the side, instead of directly under the cylinders. This way when ignition occurs, the position of the rod will be perfectly vertical and won't press the piston against the cylinder wall. Check the animated diagram on Jack's site. See where the piston rubs against the wall? That's energy lost, and power/fuel wasted. The tangential solution saves that energy. |
|
08-02-2001, 04:09 PM | #7 | |||
Pretty much amazing
|
Thanks, that helps a lot more. I understand it now.
__________________
ec437 on grammar; Quote:
Quote:
|
|||
08-04-2001, 01:48 PM | #8 | |
AF Enthusiast
Join Date: May 2001
Location: Ramstein AB
Posts: 1,240
Thanks: 0
Thanked 1 Time in 1 Post
|
No problem Mr. Porsche.
Like matt, I don't fully understand the details concerning the upstroke. If proven results have shown successful power savings, then the upstroke is most likely non-essential. But it does seem right that the rod will pressure the cylinder lining on its way up, or perhaps it will consume power from the other downward moving pistons... I will continue to search for answers. I believe that the rotary engine is still the best new (well not that new anymore) internal combustion engine. It's a shame that there aren't too many companies out there developing this proven design. Perhaps then we would be able to see a powerful yet reliable piece that would force even Felix Wankel to smile in his grave. The tangential design also seems like an obvious design improvment, but current automakers are too conservative to go out on a limb and try anything totally different. We can all emit a breath of relief, knowing that Mazda will extend its rotary line with the RX-8. Any brave souls out there willing to produce and mass-market a working tangential powerplant? |
|
|
POST REPLY TO THIS THREAD |
|
|