Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
04-13-2002, 02:05 PM | #61 | |
AF Newbie
Join Date: Apr 2002
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
reprogramming 2001 blazer remote keyless entry
Anyone know how to reprogram a 2001 blazer's remote keyless entry?
|
|
04-15-2002, 08:26 AM | #62 | ||
AF Enthusiast
Join Date: Sep 2001
Posts: 553
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: programming a ford remote
Quote:
2) Press any button on any remote. Doors should lock and unlock to acknowlege acceptance. Repeat step 2 for every extra remote. 3) Turn off ignition. Doors will lock and unlock one more time to verify exiting of programming. NOTE: All remotes must be programmed at the same time!
__________________
Why isn't common courtesy more common? |
||
04-15-2002, 09:01 AM | #63 | ||
AF Enthusiast
Join Date: Sep 2001
Posts: 553
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Programing keyless entry for 95 Aurora
Quote:
Transmitter programming can only be accomplished using a Tech 1 scan tester. See instructions included with the Tech 1. Unfortunately, unless you know a local shop with a Tech 1, you will have to go back to the dealer for programming.
__________________
Why isn't common courtesy more common? |
||
04-15-2002, 09:01 AM | #64 | ||
AF Enthusiast
Join Date: Sep 2001
Posts: 553
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: reprogramming 2001 blazer remote keyless entry
Quote:
__________________
Why isn't common courtesy more common? |
||
04-21-2002, 07:31 PM | #65 | |
AF Newbie
Join Date: Apr 2002
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
I recently bought a 94 Pontiac Grand Prix SE that came with a keyless remote entry but it didnt work. I replaced the batteries and still no avail. I tried to reprogram by how it is listed here but when I ground the wire in the trunk, the doors do not lock or do anything. I tried a jumper, I tried a coat hanger (like someone said they tried) and still nothing. What else can I do?
|
|
04-22-2002, 01:08 PM | #66 | |
AF Newbie
Join Date: Apr 2002
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
97 pontiac grand prix
I just got a new remote for my 97 pontiac grand prix se and I was wanting to know how to program it .... you have a 94 listed in here but it is different.
Thank you Rob |
|
04-22-2002, 03:03 PM | #67 | |
AF Enthusiast
Join Date: Sep 2001
Posts: 553
Thanks: 0
Thanked 0 Times in 0 Posts
|
Last two posters. I will get your answers tomorrow morning when it's quiet in here.
__________________
Why isn't common courtesy more common? |
|
04-22-2002, 03:08 PM | #68 | |
AF Newbie
Join Date: Apr 2002
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
Thank you!
Thank you very much. I really appreciate it.
|
|
04-23-2002, 04:23 PM | #69 | |
AF Newbie
Join Date: Apr 2002
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
Another one?
Hey Tireburner etal,
How about a 2002 Escalade? Thanks in advance |
|
04-23-2002, 09:42 PM | #70 | |
AF Newbie
Join Date: Apr 2002
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
98 Olds 88 LS Remote
CAN ANYONE TELL ME HOW TO REPROGRAM A REMOTE FOR A
1998 OLDS 88LS? THANK YOU |
|
04-24-2002, 08:02 AM | #71 | |
AF Enthusiast
Join Date: Sep 2001
Posts: 553
Thanks: 0
Thanked 0 Times in 0 Posts
|
Advaik :
I double checked the instructions for your Grand Prix. They are correct. Verify the orange wire at the keyless module has 12v+ all the time. If not check fuse #32. Also check the pink wire. It should show 12v+ with the key in the run position. If both test fine, try unplugging the module, then plugging it back in starting with the plug that has the black wire first. robsinfl : 1) Sit in the driver's seat 2)Remove the ignition key from the ignition lock cylinder 3)Close all the doors 4)Press and hold unlock on the door lock switch (on the door) 5)While holding the door lock switch in the unlock postition, insert and remove the ignition key twice. DO NOT ROTATE THE KEY.. JUST SLIDE IT IN AND BACK OUT. 6)Insert the ignition key the third time, leaving the kin in the ignition cylinder. DO NO TURN KEY 7)Release the door lock switch. You will hear 3 chimes indicating the transmitter programming is active. 8) Press and hold the lock and unlock buttons on the keyless entry remote at the same time (one remote) for 12 seconds. You will hear two chimes. This indicates the transmitter has been programmed. 9)Repeat step (8) for all additional transmitters to be programmed 10) Exit programming by removing the key from the ignition cylinder. Judah Hill: 1) Turn ignition switch off 2) Install a fused jumper wire (3amp fuse is suffiecient) between pin 8 (black/ white wire) and pin 4 (black wire) at the data link connector (DLC) the DLC is located under the drivers side of the dash, generally bolted to the right of the steering column 3) Close all doors 4) Turn the ignition switch on 5)Press and hold the LOCK and UNLOCK buttons on one remote (both buttons at the same time) for 30 seconds. The doors will lock then unlock 6)Repeat step (5) for each additional transmitter 7) Remove Jumper wire 8) Turn off ignition. the Wizard: I currently do not have a service manual for an 02 Escalade. When I get one I will post it for you.
__________________
Why isn't common courtesy more common? |
|
04-24-2002, 11:37 AM | #72 | |
AF Newbie
Join Date: Apr 2002
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
97 pontiac grand prix
Thank you for your effort but it doesnt work. I hear no chimes after following the instructions to the letter. I tried just in case inserting the key twice, three times, once etc... nothing works. Could you please double check. I really appreciate it.
Rob |
|
04-27-2002, 08:04 PM | #73 | |
AF Newbie
Join Date: Apr 2002
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
99 Buick Century
Tireburner:
I have a 1999 Buick Century that I just bought and I need to reprogram the remote. Can you please help me? Thank you very much! |
|
04-27-2002, 11:26 PM | #74 | |
AF Newbie
Join Date: Apr 2002
Location: Salt Lake, Utah
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
'99 Tahoe remote
Just looking for a hand in programing my '99 Tahoe remote entry fobs.
Any ideas? Thank you in advance for any help! From reading the posts here it looks like I may have found the right place and that Tireburner should start taking donations via paypal.com or some other site. ~John |
|
04-29-2002, 12:45 PM | #75 | |
AF Enthusiast
Join Date: Sep 2001
Posts: 553
Thanks: 0
Thanked 0 Times in 0 Posts
|
robsinfl:
Maybe it's a late 96 model. Try the following instructions. 1-Open trunk 2-Remove rigt rear trim panel 3-Taped to a harness near the antenna mast (sorry that's the description the book gives) is a single pin plug going no where. Wire color in that plug is probably black/white. 4-Ground that wire. The door locks will respond by locking, then unlocking 5-Press and hold Lock and Unlock buttons simultaneously for 10 seconds 6-The doors will lock then unlock indicating the system has learned that transmitter 7-Repeat step 5 for all remaining transmitters 8-Remove ground from the program jumper 9-Verify proper remote functions. The keyless reciever appears to be mounted to the right side of the right rear speaker in the trunk seperation panel. If you must go there because you can't find the program jumper where previously described, the program wire is in pin L. It is a black/white wire at the keyless reciever.
__________________
Why isn't common courtesy more common? |
|
|
POST REPLY TO THIS THREAD |
|
|