 |
 |
 |
|
|
 |
| Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
 | | ||
| |
|
| Latest | 0 Rplys |
|
|||||||
 |
 Show Printable Version |  Email this Page | 
Subscribe to this Thread
|
|
|
Thread Tools |
09-01-2006, 05:42 PM
|
#1 | |
|
AF Newbie
Join Date: Sep 2006
Location: Seaford, Delaware
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
96 Jetta DTC error code P1613
My check engine light come on this week; after a scan the DTC reported a P1613 error. I searched the web for this error and found this:
MIL Call-up Circ Open/Short to B+ Does anyone know what componet this refers to? Has anyone seen this error with their Jetta? Thanks in advance for any help, or insight you can give. buyllc |
|
|
|
|
09-11-2006, 03:13 PM
|
#2 | |
|
AF Enthusiast
 Join Date: Nov 2004
Location: Gainesville, Florida
Posts: 615
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 96 Jetta DTC error code P1613
MIL = malfunction indicatory light
The circuit between the computer and the light has an open or short to B+ (battery postive terminal). |
|
|
|
|
|
06-12-2009, 07:59 PM
|
#3 | |
|
AF Newbie
Thread starter
Join Date: Sep 2006
Location: Seaford, Delaware
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 96 Jetta DTC error code P1613
Thank you for the help. Your help solved the problem for us.
|
|
|
|
|
|
10-29-2013, 08:15 AM
|
#4 | |
|
AF Newbie
Join Date: Oct 2013
Location: ellerslie, Georgia
Posts: 3
Thanks: 6
Thanked 0 Times in 0 Posts
|
Re: 96 Jetta DTC error code P1613
i have the same code in my jetta.how do you fix this and wich "light" are you refering to?
|
|
|
|
|
|
10-29-2013, 10:58 AM
|
#5 | |
|
AF Enthusiast
Join Date: Aug 2004
Location: Porter, Indiana
Posts: 890
Thanks: 7
Thanked 74 Times in 72 Posts
|
Re: 96 Jetta DTC error code P1613
Check your grounds and wiring. This is a CEL (Check Engine Light) code for when the CEL itself is having a problem. Could be the CEL bulb is burned out.
Here are some other possibilities. - an automatic transmission ECU was installed at some point (car is manual, I recently purchased and don't have much service history). Beleiving there is an auto tranny, the MIL comes on because it does not detect auto tranny ODBII sensors. A Vag-Com needs to be used to update ECU Firmware. - "the issue was the bolt holding in the crank position censor wasn't in tight enough, so the ecu wasn't getting any info back from the sensor, resulting in the code." Solution: plug in sensor - There is a grounded wire between ECU and MIL. Cluster needs to be removed and wires tested for ground. Last edited by 65comet; 10-29-2013 at 10:59 AM. Reason: typo |
|
|
|
|
| The Following User Says Thank You to 65comet For This Useful Post: |
racole1980 (10-30-2013)
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
