Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Chevrolet > Avalanche | C&K | Silverado | Suburban | Tahoe > Tahoe
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools Search this Thread
Old 06-21-2003, 06:28 AM   #1
muttd4h
AF Newbie
 
Join Date: Jun 2003
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
2001 Tahoe Keyless Entry Programming

Morning,

I noticed a couple of threads on this issue but none specific to the 2001. Anyone out there have any thoughts or ideas? Just purchased this machine and a couple of remotes off the internet but I don't have anything in the manual to show me how to do this. Thanks in advance.

Rick Herrick
Raleigh, NC
muttd4h is offline   Reply With Quote
Old 06-21-2003, 11:31 AM   #2
Shortbus
Blah blah blah
 
Join Date: Aug 2002
Location: Auburn
Posts: 15,481
Thanks: 3
Thanked 3 Times in 3 Posts
Send a message via AIM to Shortbus
Document ID# 660746
2001 Chevrolet/Geo Tahoe - 4WD

--------------------------------------------------------------------------------

Transmitter Programming

Important
All transmitters which are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.


You may program up to 4 transmitters, using either of the two following procedures:

Transmitter Programming Procedure (Method 1 - No Tools Required)
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Transmitter Programming Procedure (Method 2 - Scan Tool Required)
Install a scan tool.
Turn the ignition ON, with the engine OFF.
Use the scan tool in order to access the Body Control Module (BCM) Special Function: Program Key Fobs menu.
Follow the directions on the scan tool in order to program the transmitters.
Operate the transmitter functions in order to verify correct system operation.

--------------------------------------------------------------------------------
Document ID# 660746
2001 Chevrolet/Geo Tahoe - 4WD
Shortbus is offline   Reply With Quote
Old 06-21-2003, 12:55 PM   #3
muttd4h
AF Newbie
Thread starter
 
Join Date: Jun 2003
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Thanks very much John. This board is excellent. Not only did I get a very quick answer but I got an email telling me the post was ready for me. Thanks again...

Rick Herrick
muttd4h is offline   Reply With Quote
Old 06-21-2003, 01:00 PM   #4
Shortbus
Blah blah blah
 
Join Date: Aug 2002
Location: Auburn
Posts: 15,481
Thanks: 3
Thanked 3 Times in 3 Posts
Send a message via AIM to Shortbus
No problem Rick, I email'd you back but for some reason the email keeps bouncing back to me. I am sure it is something on my end though.

Have a good one
Shortbus is offline   Reply With Quote
Old 06-23-2003, 07:18 PM   #5
DMC12
DeLorean Guy
 
DMC12's Avatar
 
Join Date: Feb 2002
Location: Hazard, Kentucky
Posts: 1,899
Thanks: 0
Thanked 0 Times in 0 Posts
John, I bought a keyless entry reciever box & key fob transmitter on eBay. I was hoping to install them but can't figure out where the reciever plugs into. My repair manual seems to have left this out of the wiring diagram... any ideas?
__________________
SOLID! crew (circa 2002).
DeLorean moderator.
DMC12 is offline   Reply With Quote
Old 06-24-2003, 12:11 PM   #6
Shortbus
Blah blah blah
 
Join Date: Aug 2002
Location: Auburn
Posts: 15,481
Thanks: 3
Thanked 3 Times in 3 Posts
Send a message via AIM to Shortbus
Quote:
Originally posted by DMC12
John, I bought a keyless entry reciever box & key fob transmitter on eBay. I was hoping to install them but can't figure out where the reciever plugs into. My repair manual seems to have left this out of the wiring diagram... any ideas?
Let me know if this is what you need or not.



Shortbus is offline   Reply With Quote
Old 06-24-2003, 01:02 PM   #7
DMC12
DeLorean Guy
 
DMC12's Avatar
 
Join Date: Feb 2002
Location: Hazard, Kentucky
Posts: 1,899
Thanks: 0
Thanked 0 Times in 0 Posts
You're amazing!!!!!!!!!!!!!!


What is "4" in this map? The underside of the dash? Or looking at the steering column from the floor?





__________________
SOLID! crew (circa 2002).
DeLorean moderator.
DMC12 is offline   Reply With Quote
Old 06-24-2003, 01:10 PM   #8
Shortbus
Blah blah blah
 
Join Date: Aug 2002
Location: Auburn
Posts: 15,481
Thanks: 3
Thanked 3 Times in 3 Posts
Send a message via AIM to Shortbus
4 is the plastic cage part of the dash viewing from the top. It is w/o the upper trim pad in place.
Shortbus is offline   Reply With Quote
Old 07-07-2003, 12:35 AM   #9
DMC12
DeLorean Guy
 
DMC12's Avatar
 
Join Date: Feb 2002
Location: Hazard, Kentucky
Posts: 1,899
Thanks: 0
Thanked 0 Times in 0 Posts
Pulling that dash apart without a guide was very, um, interesting Guess its time to buy the big expensive book (not the useless Pep Boys rag).

Anyway, thanks for the help John! It looks like the black box & fob I got off eBay were defective... I get no lock-unlock telling me that I'm in program mode. I wonder if a good mechanic would be able to scan that component thru the OBD2 port to see if its operational
__________________
SOLID! crew (circa 2002).
DeLorean moderator.
DMC12 is offline   Reply With Quote
Old 07-12-2003, 11:49 AM   #10
ortegaj
AF Newbie
 
Join Date: Jul 2003
Location: Sun Valley, California
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Question Differences in remotes

I went hiking the other night and I lost one of my receivers. The dealer is charging me $68 to replace the transmitter. I just bought two transmitters on Ebay, but I'm not sure if they'll work because of the numbers on the back of the remotes.

My original control has the following numbers:
GM/LEAR 15042968
FCCID: KOBLEAR1XT
CANADA 3521 102 1718

The controls I just bought have the following numbers:
GM/LEAR 15042805
FCCID: KOBLEAR1XT
CANADA 3521 102 1718


Did I just buy two remotes that will not work on my truck or will I be able to program the three remotes.

Any help will be appreciated.

Thanks for all the detail explanations on all the other posts.
ortegaj is offline   Reply With Quote
Old 07-12-2003, 12:20 PM   #11
Shortbus
Blah blah blah
 
Join Date: Aug 2002
Location: Auburn
Posts: 15,481
Thanks: 3
Thanked 3 Times in 3 Posts
Send a message via AIM to Shortbus
Re: Differences in remotes

Quote:
Originally posted by ortegaj
I went hiking the other night and I lost one of my receivers. The dealer is charging me $68 to replace the transmitter. I just bought two transmitters on Ebay, but I'm not sure if they'll work because of the numbers on the back of the remotes.

My original control has the following numbers:
GM/LEAR 15042968
FCCID: KOBLEAR1XT
CANADA 3521 102 1718

The controls I just bought have the following numbers:
GM/LEAR 15042805
FCCID: KOBLEAR1XT
CANADA 3521 102 1718


Did I just buy two remotes that will not work on my truck or will I be able to program the three remotes.

Any help will be appreciated.

Thanks for all the detail explanations on all the other posts.
The number 15042805 does not cross reference to anything that I know of.

Your year does have two different designs that were used, with the remote cast numbers of 15042806 and 15042803.

I have no idea what the 15042805 number means

I would be just be guessing whether they would work or not.

I say give it a try, as long as the button configuration looks the same they may work.

The worst that could happen is you will have to reprogram your original transmitter to work again since programming clears all of the transmitters.
Shortbus is offline   Reply With Quote
Old 07-12-2003, 02:18 PM   #12
ortegaj
AF Newbie
 
Join Date: Jul 2003
Location: Sun Valley, California
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Thanks for the info. Now, I just have to wait for the remotes to arrive and I will try them since they do look exactly alike. If not I'll just re-sell them and buy another that matches mine exactly. I will though keep instructions on how to program the transmitter for future reference.

I'll keep my fingers crossed.

Thanks!!
ortegaj is offline   Reply With Quote
Old 02-16-2005, 11:41 PM   #13
k71
AF Newbie
 
Join Date: Feb 2005
Location: portland, Oregon
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Key Less / Remote Memory Settings

Sounds like we have a lot of knowledgable people. Here's my question regarding key less remotes and memory seating etc.

Have a new '05 Z71 and have had difficulty with the memory seats. Neither the drivers side memory buttons (1 or 2) seem to maintain the saved setting, nor do the keys or remote. Wanted to see if anyone else is having a similar problem with the '05. Also wondering if I'm correct in assuming that the remote controls should be able to trigger the memory setting as well as the driver memory buttons - my understanding from the sales person.

thanks
k71 is offline   Reply With Quote
Old 07-20-2006, 08:21 AM   #14
scopeland
AF Newbie
 
Join Date: Jul 2006
Location: Moncks Corner, South Carolina
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Re: 2001 Tahoe Keyless Entry Programming

Help!!!! My keyless entry quit working. I replaced the battery and reprogrammed the remote but it still wont work. Can anyone give me any more suggestions?
scopeland is offline   Reply With Quote
Old 06-12-2010, 07:19 PM   #15
Rapidray
AF Newbie
 
Join Date: May 2007
Location: zellwood, Florida
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Question Key & Keyless entry clicker found.

I found keys and a clicker. Is there any way to find the owner from the
info off the clicker? this may be a dumb question buy I'm just trying to
get the keys to the owner.
Clicker reads:GM/Lear 25695954 FCC ID:KOBLEAR1XT.
Thanks, Rapidray
Rapidray is offline   Reply With Quote
 
Similar Threads
Thread Thread Starter Forum Replies Last Post
'09 Corolla KeyFOB, keyless entry programming Question btrolla Corolla/Matrix/Voltz 1 09-03-2010 01:00 PM
94 s10 remote keyless entry programing instructions needed stillblazin Problem Diagnosis 0 07-01-2009 10:39 PM
2003 Tahoe Keyless Entry Programming azjay Tahoe 3 03-12-2008 11:36 AM
1998 Tahoe Keyless Entry Programming Raistmaj Tahoe 11 12-15-2005 09:26 AM
95 tahoe keyless entry programming Wink C/K 3 08-07-2004 11:02 PM

Reply

POST REPLY TO THIS THREAD


Bookmarks
Go Back   Automotive Forums .com Car Chat > Chevrolet > Avalanche | C&K | Silverado | Suburban | Tahoe > Tahoe

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 10:12 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts