Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Engineering/Technical
Engineering/Technical Ask technical questions about cars. Do you know how a car engine works?
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 09-19-2017, 02:01 PM   #1
adampro1
AF Newbie
 
Join Date: Sep 2017
Location: park ridge, Illinois
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
1972 Charger Thermostat

How would I go about replacing the thermostat on a 318 engine on my 72 charger?
adampro1 is offline   Reply With Quote
Old 10-10-2017, 03:01 AM   #2
Dave B.
AF Regular
 
Dave B.'s Avatar
 
Join Date: Mar 2012
Location: Southern, Ohio
Posts: 131
Thanks: 0
Thanked 24 Times in 24 Posts
Re: 1972 Charger Thermostat

First, it's a good idea to drain some coolant from the system. One or two quarts should do it. There's usually a little valve (called a 'petcock') down low on one side of the radiator. It looks a bit like a flat wingnut. Put a BIG pan under the car below the petcock because the flow of coolant is somewhat unpredictable. The reason you're draining the coolant is that the level of coolant in the radiator is usually higher than that in the engine and it will flood out while you're working on the thermostat...
Next, trace the upper radiator hose from the radiator back to the intake manifold on the engine.
At that point, you'll find a rounded metal thermostat housing bolted to the intake manifold. It's usually a good idea to loosen the clamp and separate the upper hose from the thermostat housing at this time.
Next, remove the two bolts securing the housing and lift it straight up. You may have to pry gently around the edge, as there's usually sealant there.
Remove the old gasket completely, gently scraping the mating surfaces as required. The round part inside is the thermostat. Be sure to take note that there is usually a 'pointed' side that sticks up.
Using paper towels or something similar, make sure that the mating surfaces are clean and dry.
Install the new thermostat in the manifold, replace the gasket and the thermostat housing, then re-install the two bolts. Before doing this, you may want to add a THIN coating of sealant on the new gasket for insurance.
Warning: Thermostat housings are usually made of cast aluminum or pot-metal and are VERY easy to crack/break!! If you have access to a torque wrench, be sure to tighten the bolts evenly, moving back and forth from one to the other in small steps. Torque settings can be found on the internet. If you don't have a torque wrench, tighten the bolts evenly and securely, but don't go overboard pulling on the wrench!
Re-install the radiator hose, start the car and refill the radiator - you're finished!

Last edited by Dave B.; 10-10-2017 at 08:38 AM.
Dave B. is offline   Reply With Quote
The Following User Says Thank You to Dave B. For This Useful Post:
shorod (10-11-2017)
 
Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums .com Car Chat > Engineering/Technical

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 05:04 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts