Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Toyota > Sequoia
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools Search this Thread
Old 10-05-2004, 05:14 AM   #16
david_vu04
AF Newbie
 
Join Date: Oct 2004
Location: westminster
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Need help Programing a blank Master key for Lexus Is 300

This might be off topic a bit, but i need help Programing a blank Master key for Lexus Is 300
david_vu04 is offline   Reply With Quote
Old 11-19-2004, 12:09 PM   #17
bretbowman
AF Newbie
 
Join Date: Nov 2004
Location: Cincinnati, Ohio
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Programming keyless Entry Remote AND Transponder Key

My wife and I just purchased a 2002 Toyota Sequoia Limited 2WD. I wanted to see if I could get anyone to send me the procedure for the following:

1. Clear all from computer in case it's full
2. Add/Program Keyless entry remote control
3. Add/Program Blank Transponder key into a Master copy key
4. Add/Program Blank Transponder key into Valet copy key
5. Difference in procedures for different year models
6. Similarities to other model Toyotas (such as Tacoma, etc.)

If someone can send me these instructions (preferrably the .pdf from Toyota), I can post these on my permanent website with a easy to remember URL for anyone to refer too.

I'm seeking assistance with this for my own toyota, but would love to be able to assist or help others any way that I can. I have virtually unlimited storage space and a generous 768k upload speed with static ip, so hopefully this is a good asset to offer.

As always thanks in advance to any who can assist. Your assistance NEVER goes unappreciated by us in this forum.

Sincerely,
Bret Bowman
bretbowman@yahoo.com
bretbowman is offline   Reply With Quote
Old 12-12-2004, 10:34 AM   #18
sandmanva
AF Newbie
 
Join Date: Dec 2004
Location: Virginia beach, Virginia
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
05 Sequoia number of keys?

I just bought a 05 Sequoia. I misplace my keys alot, so my solution has always been to have extra sets. Is it possible to program more than 4 keys for the truck? I just paid a boatload of cash at the dealership to program five keys and was then was told only fours keys were possible. Now I have a cut key that will not start the truck. With Nissan it was easy to buy remote off of ebay and program them myself. Toyota makes it much harder in 05. Can anyone send me the sequence for the keys and the remotes for future.Is it as hard as the dealer makes it out to be? lol@cox.net thnkas dave
sandmanva is offline   Reply With Quote
Old 03-04-2005, 05:22 PM   #19
Camry02LE
AF Newbie
 
Join Date: Mar 2005
Location: Stroudsburg, Pennsylvania
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Re: Program Toyota Master Key

Quote:
Originally Posted by sequoia01
Instructions for programming a transponder key.

Prerequisites:
blank transponder key (eBay.com - $20).
pre-programmed master "black" key for the vehicle.


Programming spare keys: for 1998 to 2002

1.. Copy the cuts of the original working key onto the appropriate
transponder blank.

2.. Enter the car and close all of the doors.

3.. Simultaneously depress and release both the brake and accelerator pedals.

4.. Within five seconds, insert a working pre-programmed key into the ignition cylinder, and turn to the "on" position.

5.. Within fifteen seconds of turning the ignition, depress and release
the accelerator pedal five times for a primary key. (Depress and release four times for a valet key.)

6.. Within twenty seconds, depress and release the brake pedal six times for a primary key. (Depress and release only times for a valet key.)

7.. Turn the ignition to the "off" position and immediately remove the
key.

8.. Within ten seconds of removing the key, insert the new key and turn it to the "on" position.

9.. Within ten seconds, depress and release the accelerator pedal once. The security light will then flash for 60 seconds and then turn off. When the security light stops flashing the programming should be complete.

10.. Start the vehicle to verify that programming was successful.

FOR 2002+
1.Make sure all doors and windows are closed.
2.Insert master key into the ignition cylinder.
3.Cycle the ignition cylinder from ON to OFF 5 times.
4.Open and close the driver side door 6 times.
5.Remove the master key and insert the new duplicate key.
6.DO NOT TURN THE IGNITION CYLINDER ON
7.The new key will be registered after 60 seconds.The THEFT light on the
dashboard will go out,indicating that programming has been completed.
"some 2002 will work using the 1998+ programming."

Thank you for the instructions. I just bought a 2002 Camry LE V6, but only have one black key (I assumed its the master key). Will this instruction work for my car? I was told you can only program up to 3 keys. How do I erase all previous keys, and then add my new one. I did purchase a transponder key off Ebay, but their instructions don't work. I asked for alternate instructions, but just have no luck. My dash do not have a THEFT light, so I assumed I should use the 1998-2002 instructions. But how do I reset all previous keys? I will appreciate if you can e-mail me the instruction in PDF file, kietman35@gmail.com. Thanks in advance for any help you can provide.
Camry02LE is offline   Reply With Quote
Old 05-25-2005, 12:31 AM   #20
GuyF
AF Newbie
 
Join Date: May 2005
Location: Asutin, Texas
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Re: Re: Re: Program Toyota Master Key

I am willing to send you a PDF file from TOYOTA dealer manual that included everything you need to program your key. Please leave your email address

Would you be able to send me the pdf to program a key for a 2001 sequoia?

Thank you very much
GuyF is offline   Reply With Quote
Old 05-25-2005, 12:38 AM   #21
GuyF
AF Newbie
 
Join Date: May 2005
Location: Asutin, Texas
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Re: Re: Re: Program Toyota Master Key

Quote:
Originally Posted by MYSEQUOIA03
Mike,
Like I said from my previous posted, 2001/2002 Transponder key have difference chip from 2003 and 2004. Make sure you have correct part number.
I am willing to send you a PDF file from TOYOTA dealer manual that included everything you need to program your key. Please leave your email address

Mysequoia03
Could you please send me the procedure to program a key for a 2001 sequoia at gferraro@swbell.net?

Thank you very much
GuyF is offline   Reply With Quote
Old 10-25-2005, 10:40 AM   #22
OkHumourMe
AF Newbie
 
Join Date: Oct 2005
Location: Dublin
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Question Re: Re: Program Toyota Master Key

Quote:
Originally Posted by sequoia01
Instructions for programming a transponder key.

Prerequisites:
blank transponder key (eBay.com - $20).
pre-programmed master "black" key for the vehicle.


Programming spare keys: for 1998 to 2002

1.. Copy the cuts of the original working key onto the appropriate
transponder blank.

2.. Enter the car and close all of the doors.

3.. Simultaneously depress and release both the brake and accelerator pedals.

4.. Within five seconds, insert a working pre-programmed key into the ignition cylinder, and turn to the "on" position.

5.. Within fifteen seconds of turning the ignition, depress and release
the accelerator pedal five times for a primary key. (Depress and release four times for a valet key.)

6.. Within twenty seconds, depress and release the brake pedal six times for a primary key. (Depress and release only times for a valet key.)

7.. Turn the ignition to the "off" position and immediately remove the
key.

8.. Within ten seconds of removing the key, insert the new key and turn it to the "on" position.

9.. Within ten seconds, depress and release the accelerator pedal once. The security light will then flash for 60 seconds and then turn off. When the security light stops flashing the programming should be complete.

10.. Start the vehicle to verify that programming was successful.

FOR 2002+
1.Make sure all doors and windows are closed.
2.Insert master key into the ignition cylinder.
3.Cycle the ignition cylinder from ON to OFF 5 times.
4.Open and close the driver side door 6 times.
5.Remove the master key and insert the new duplicate key.
6.DO NOT TURN THE IGNITION CYLINDER ON
7.The new key will be registered after 60 seconds.The THEFT light on the
dashboard will go out,indicating that programming has been completed.
"some 2002 will work using the 1998+ programming."


Great Postings Folks,
I have a question on the instructions above...
DO you have to have the MASTER key to program the new key? OR... Can I program a new Blank tansponder from the Grey Valet key?

And I f it is possible to program a new Master key fromt he Grey key... then is this a Real master key or is it really a Clone?

Thanks in advance
P.
OkHumourMe is offline   Reply With Quote
Old 12-06-2005, 01:19 PM   #23
cvayala
AF Newbie
 
Join Date: Dec 2005
Location: Atwater, California
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Program Toyota Master Key

I registered just to confirm that the procedure worked on my recently purchased 2002 Camry LE V6.

By the way, the reason you need a master key is to confirm to the vehicle that you are the owner. Or another way to say this is to prevent a valet (or whoever you give the grey key to) from programming a master key for your car.
cvayala is offline   Reply With Quote
Old 12-06-2005, 07:48 PM   #24
madhouze
AF Newbie
 
Join Date: Dec 2005
Location: Jersey City, New Jersey
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Help!

It has been quite a long time since people wrote in here, but i will try my luck anyway:
I purchased a 2005 toyota Matrix XR.
Installed Viper 791VX with remote start, and now bought a few blank transponder keys so i can use the remote start.
I have found over the net a few instruction for programming the keys, but cannot complete any of them.
PLEASE! advise?

Thanks,
Ohadidan@gmail.com
madhouze is offline   Reply With Quote
Old 08-20-2006, 10:58 PM   #25
hopphan
AF Newbie
 
Join Date: Aug 2006
Location: Garland, Texas
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Program Toyota Master Key

Quote:
Originally Posted by MYSEQUOIA03
Mike,
Like I said from my previous posted, 2001/2002 Transponder key have difference chip from 2003 and 2004. Make sure you have correct part number.
I am willing to send you a PDF file from TOYOTA dealer manual that included everything you need to program your key. Please leave your email address

Mysequoia03

Hi Mysequoia03

The post too old now, wish you still read it and help me with this.
I had sequoia03 and just bought and cut the new key, but don't know how to programming, would you please share to me the pdf file so I try to program the new key. (hopphan@yahoo.com)

Thank you
hopphan is offline   Reply With Quote
Old 10-16-2006, 11:50 AM   #26
sohail43r
AF Newbie
 
Join Date: Oct 2006
Location: Doha
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Program Toyota Master Key

I have lost my Master key of toyota camry 2001 4 cyl. i have purchase new blank key from toyota and make cut , i'm able to open all door but engine is not working. key need to program. or some other idea to run my engine . thanks
sohail43r is offline   Reply With Quote
Old 10-21-2006, 10:29 PM   #27
sohail43r
AF Newbie
 
Join Date: Oct 2006
Location: Doha
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Program Toyota Master Key

Quote:
Originally Posted by GuyF
I am willing to send you a PDF file from TOYOTA dealer manual that included everything you need to program your key. Please leave your email address

Would you be able to send me the pdf to program a key for a 2001 sequoia?

Thank you very much
hello ,
I have lost my all master keys, but I have one duplicate which can open all doors even can move switch bt engine does't start. i have purchase new blank key from ebay, could you guide me how to program new key without master .... as i dont have nay master.. i make cut similar to normal duplicate key... thansk my email : sohail43r@hotmail.com
sohail43r is offline   Reply With Quote
Old 01-26-2007, 02:30 PM   #28
skillzunlimited
AF Newbie
 
Join Date: Jan 2007
Location: pittsbirgh, Pennsylvania
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Program Toyota Master Key

Can u email those directions to me as well? salvin@excite.com
skillzunlimited is offline   Reply With Quote
Old 01-27-2007, 07:24 PM   #29
jws13
AF Newbie
 
Join Date: Jan 2007
Location: williamsburg, Virginia
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Program Toyota Master Key

Can someone tell me how to program the keyless remote for a 2005 Sequoia?
jws13 is offline   Reply With Quote
Old 02-02-2007, 01:19 PM   #30
skillzunlimited
AF Newbie
 
Join Date: Jan 2007
Location: pittsbirgh, Pennsylvania
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Program Toyota Master Key

Quote:
Originally Posted by MYSEQUOIA03
Mike,
Like I said from my previous posted, 2001/2002 Transponder key have difference chip from 2003 and 2004. Make sure you have correct part number.
I am willing to send you a PDF file from TOYOTA dealer manual that included everything you need to program your key. Please leave your email address

Mysequoia03
would u email the directions to skillzunlimited@comcast.net Thank you
skillzunlimited is offline   Reply With Quote
 
Similar Threads
Thread Thread Starter Forum Replies Last Post
1999 Toyota 4Runner Key Problem mmahan69 4Runner/GX470 1 02-03-2011 12:30 AM
2005 toyota camry LE master key and remote programming ny17 Camry/Camry Hybrid/Vista 2 06-23-2009 04:50 PM
'04 Master Key duplicate programming steps? solara04nubie Solara 1 04-21-2008 12:30 PM
program master key 2003 camry sequence? camry03 Camry/Camry Hybrid/Vista 0 09-30-2004 10:09 AM

Reply

POST REPLY TO THIS THREAD


Bookmarks
Go Back   Automotive Forums .com Car Chat > Toyota > Sequoia

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 01:29 AM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts