 |
 |
 |
|
|
 |
| Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
 | | ||
| |
|
| Latest | 0 Rplys |
|
|||||||
 |
 Show Printable Version |  Email this Page | 
Subscribe to this Thread
|
|
|
Thread Tools |
07-04-2017, 09:57 PM
|
#31 | |
|
Registered Offender
 
Join Date: Mar 2006
Location: Rural
Posts: 6,518
Thanks: 6
Thanked 341 Times in 336 Posts
|
Re: New Starter Will Spin - Won't Engage
Parasitic drain is commonly around 150mA on newer vehicles. 0.7V seems a little high, but that depends heavily upon the health of the battery.
__________________
Permanent seat assignment on the Group W bench... Automotive Forums Survival Guide Last edited by Blue Bowtie; 07-06-2017 at 08:31 PM. |
|
|
|
| The Following User Says Thank You to Blue Bowtie For This Useful Post: |
ChevyMan1989 (07-04-2017)
|
|
07-04-2017, 09:58 PM
|
#32 | |
|
AF Newbie
 Join Date: Jul 2017
Location: Mansfield, Ohio
Posts: 26
Thanks: 14
Thanked 0 Times in 0 Posts
|
Re: New Starter Will Spin - Won't Engage
Voltage is dropping quickly now too. Not cranking or doing anything just having a scanner hooked up and I lost 2 volts in the matter of 40 minutes. The battery is now down to 10 volts..
|
|
|
|
|
|
07-04-2017, 10:01 PM
|
#33 | |
|
AF Newbie
Join Date: Jul 2017
Location: Mansfield, Ohio
Posts: 26
Thanks: 14
Thanked 0 Times in 0 Posts
|
Re: New Starter Will Spin - Won't Engage
Another question for you. How hard should it be to turn the crank pulley without belt on, with a 1/2" socket wrench? I tried this a little bit ago and find it near impossible. I'm an active guy weighing 247 lb and at first it seemed to be turning ok but then it got to the point where I couldn't turn it at all?
|
|
|
|
|
|
07-04-2017, 10:23 PM
|
#34 | |
|
AF Newbie
Join Date: Jul 2017
Location: Mansfield, Ohio
Posts: 26
Thanks: 14
Thanked 0 Times in 0 Posts
|
Re: New Starter Will Spin - Won't Engage
Got connection to ECM again. The ECM fuse was blown. Now trying to figure out what caused it... the only thing I know is I hear some noise almost like a screeching noise comeing from inside the traverse right near where the positive cable goes from the battery under the carpet. I've checked it out though and it looks good. All wiring looks ok...
|
|
|
|
|
|
07-05-2017, 08:28 AM
|
#35 | ||
|
AF Enthusiast
Join Date: Dec 2001
Location: clarksville, Tennessee
Posts: 1,703
Thanks: 23
Thanked 183 Times in 179 Posts
|
Re: New Starter Will Spin - Won't Engage
Quote:
__________________
Post back, that's what makes Forums Work. |
||
|
|
|
| The Following User Says Thank You to aleekat For This Useful Post: |
ChevyMan1989 (07-05-2017)
|
|
07-05-2017, 06:47 PM
|
#36 | |
|
AF Newbie
Join Date: Jul 2017
Location: Mansfield, Ohio
Posts: 26
Thanks: 14
Thanked 0 Times in 0 Posts
|
Re: New Starter Will Spin - Won't Engage
Next update:
Somehow the fuel pump was on/running/making noise while the key was off and I was looking over the ground wires under the hood? How is this possible and is this normal? |
|
|
|
|
|
07-06-2017, 05:01 PM
|
#37 | |
|
AF Fanatic
Join Date: Jul 2011
Location: Worcester, Massachusetts
Posts: 5,017
Thanks: 70
Thanked 618 Times in 610 Posts
|
Re: New Starter Will Spin - Won't Engage
You need a min of 9.6 volts while cranking or the PCM will not function....
|
|
|
|
|
| The Following User Says Thank You to Tech II For This Useful Post: |
ChevyMan1989 (07-06-2017)
|
|
07-06-2017, 05:29 PM
|
#38 | |
|
AF Newbie
Join Date: Jul 2017
Location: Mansfield, Ohio
Posts: 26
Thanks: 14
Thanked 0 Times in 0 Posts
|
Re: New Starter Will Spin - Won't Engage
Got it to start somehow! I just came home today and tried to start it and it fired up? It was still hard but it fired up and ran rough for 5 minutes. Now t starts up instantly and runs pretty smooth.
BUT I ran my scanner on it and it's running rich on both bank by -10 and the fuel pressure has reached 731psi??????!!! Is it a bad sensor or something. That fuel pressure is crazy. |
|
|
|
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
