Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Chevrolet > Beretta
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 09-14-2011, 11:07 AM   #1
tp1260
AF Newbie
 
Join Date: May 2010
Location: st. petersburg, Florida
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Is it possilbe to read codes for a 95 beretta?

I was trying to run codes for my 95 beretta , when i noticed the black ALDL diagnostic connecter only had 2 terminals on it.

There is the A terminal which is on the top right, and one directly below it, and that is it.
I did not try to touch them together, but if i can get some verification i would like to know if this code reading can be done without a scan tool.

Btw, the car runs ok, but when idling, and any load , like the electric fan and or air conditioner start, it needs a foot on the gas to continue to idle.
And finally, for the first time, i saw the service engine soon light, while the car was running. Any suggestions??
tp1260 is offline   Reply With Quote
Old 09-19-2014, 10:53 PM   #2
droz313
AF Newbie
 
Join Date: Sep 2014
Location: Eastpointe, Michigan
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Is it possilbe to read codes for a 95 beretta?

Unfortunately you are stuck in the ODB 1.5 debacle. Very few scanners actually read these as it's a mixture of ODB1 codes and some ODB2. You can read a little about it on Wikipedia:

http://en.wikipedia.org/wiki/On-boar...ostics#OBD-1.5

I have a 95 Corsica that I've never been able to read the codes for. I've heard GM Tech 1 will read it, but I've taken it to a few dealers that couldn't do it.
droz313 is offline   Reply With Quote
Old 09-20-2014, 09:10 AM   #3
Blue Bowtie
Registered Offender
 
Blue Bowtie's Avatar
 
Join Date: Mar 2006
Location: Rural
Posts: 6,512
Thanks: 6
Thanked 341 Times in 336 Posts
Re: Is it possilbe to read codes for a 95 beretta?

I have a Snap-On MT-2500 scanner that will read and control OBD1, 1.5, and OBDII ECMs/PCMs - Fully bidirectional. Many shops used to possess these as their primary diagnostic tools, and many will probably still have one tucked away somewhere with the correct adapters. Ask around. You might even be able to buy one less expensively than you might think.
__________________
Permanent seat assignment on the Group W bench...
Automotive Forums Survival Guide
Blue Bowtie is offline   Reply With Quote
Old 09-20-2014, 11:42 AM   #4
Tech II
AF Fanatic
 
Join Date: Jul 2011
Location: Worcester, Massachusetts
Posts: 5,017
Thanks: 70
Thanked 618 Times in 610 Posts
Re: Is it possilbe to read codes for a 95 beretta?

I don't think so Blue.....

If you just want to read codes for 1.5I, that will take an upscale high priced scannner to do that, compared to a code reader for OBDII cars, for 20 bucks....

Even GM's Tech I couldn't read them without an adapter....the Tech II can, if you have $2500 hanging around....
Tech II is offline   Reply With Quote
Old 09-20-2014, 03:56 PM   #5
droz313
AF Newbie
 
Join Date: Sep 2014
Location: Eastpointe, Michigan
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Is it possilbe to read codes for a 95 beretta?

Quote:
Originally Posted by Tech II View Post
I don't think so Blue.....

If you just want to read codes for 1.5I, that will take an upscale high priced scannner to do that, compared to a code reader for OBDII cars, for 20 bucks....

Even GM's Tech I couldn't read them without an adapter....the Tech II can, if you have $2500 hanging around....
Are you sure a Tech 2 will read it? I know a dealer tried a Tech 2 and it didn't work.
droz313 is offline   Reply With Quote
Old 11-16-2014, 06:39 AM   #6
Blue Bowtie
Registered Offender
 
Blue Bowtie's Avatar
 
Join Date: Mar 2006
Location: Rural
Posts: 6,512
Thanks: 6
Thanked 341 Times in 336 Posts
Re: Is it possilbe to read codes for a 95 beretta?

Vehicles I've read with the MT-2500:

1995 LeSabre
1994 Impala SS
1995 Blazer, including ABS and TCCM
1995 Camaro
1995 Lumina
1995 Cutlass
1995 Grand Am, including EBCM
__________________
Permanent seat assignment on the Group W bench...
Automotive Forums Survival Guide
Blue Bowtie is offline   Reply With Quote
Old 11-16-2014, 07:54 AM   #7
Tech II
AF Fanatic
 
Join Date: Jul 2011
Location: Worcester, Massachusetts
Posts: 5,017
Thanks: 70
Thanked 618 Times in 610 Posts
Re: Is it possilbe to read codes for a 95 beretta?

Yes, a Tech II can read it.....and i am sure an MT 2500 can also.....

Went to EBay to check on prices for the MT 2500......a lot of prices were in the 600-1000 range, but there was one, in bidding around 100....but I doubt it will stay that low or might be pulled....
Tech II is offline   Reply With Quote
Old 11-16-2014, 01:50 PM   #8
Blue Bowtie
Registered Offender
 
Blue Bowtie's Avatar
 
Join Date: Mar 2006
Location: Rural
Posts: 6,512
Thanks: 6
Thanked 341 Times in 336 Posts
Re: Is it possilbe to read codes for a 95 beretta?

Ouch! That's a bit more pricey than I remember. Mine was less than $1K with a ton of adapters, troubleshooting and comm modules, power supply adapters, and the all-important cable.
__________________
Permanent seat assignment on the Group W bench...
Automotive Forums Survival Guide
Blue Bowtie is offline   Reply With Quote
Old 10-18-2018, 09:00 AM   #9
mikehuggins873
AF Newbie
 
Join Date: Oct 2018
Location: west plains, Missouri
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
Re: Is it possilbe to read codes for a 95 beretta?

if your check engine lights works not on but when you turn the key on it luminates there is a real expensive tester that works for all gm obdi take a paper clip unwind it straighten it out bend it in half insert one end into one hole and the other end into the other hole get pen and paper turn key into run engine off position the check engine light will start blinking count blinks beteween a brief pause ++++ +++++++ example 47 +++ +++++ 35 a dodge is a lot easier key on/off 3 times final turn leave in on position a form a old analog meter leads into obd port same a paper clip hope this helps ya
mikehuggins873 is offline   Reply With Quote
Old 10-18-2018, 08:10 PM   #10
Blue Bowtie
Registered Offender
 
Blue Bowtie's Avatar
 
Join Date: Mar 2006
Location: Rural
Posts: 6,512
Thanks: 6
Thanked 341 Times in 336 Posts
Re: Is it possilbe to read codes for a 95 beretta?

The problem with the jumper method is that it doesn't work with OBD1½ systems. Many GM vehicles in 1994 and 1995 were of that variety. I have a '94 Impala with that type PCM, and had a '95 Buick with that same type. Only a Tech II or MT-2500 would read it.
__________________
Permanent seat assignment on the Group W bench...
Automotive Forums Survival Guide
Blue Bowtie is offline   Reply With Quote
 
Similar Threads
Thread Thread Starter Forum Replies Last Post
Sienna "Commercial" model name/code for export britholio Sienna 1 08-12-2010 08:29 PM
read codes for 95 6cyl 4WD kpring Older Pickups 7 09-11-2008 08:42 PM
how to read codes without a code reader 72corvette Alero 1 11-20-2004 10:44 PM
reading codes with Creader code reader donaldd34 Passat 2 10-09-2004 01:18 PM
Couple of engine codes for your reading pleasure... BigBadWimp Explorer | Explorer Sport Trac 0 10-07-2004 09:59 AM

Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums .com Car Chat > Chevrolet > Beretta

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:46 AM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts