Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
11-08-2007, 01:34 PM | #1 | |
AF Regular
Join Date: Sep 2007
Location: Pasadena, Texas
Posts: 131
Thanks: 0
Thanked 0 Times in 0 Posts
|
lowering/ tire wear question
ok well the situation is that i am about to purchase the eibach lowering springs but i am not planning to buy the rear adjustable arms to do proper aligment in the rear..... so my question is if i install the eibach springs, will i get extreme tire wear in the rear, even after trying to align it the best possible without the rear adjustable arms ??because if that the case then i might as well just leave it stock height right???
__________________
97 3kgt sohc.... intake, custom exhaust, 3sx crank pulley, JVC head unit, pioneer speakers all around for highs and mids amped, 12"JBL power series sub.... |
|
11-08-2007, 02:06 PM | #2 | |
AF Enthusiast
Join Date: Jan 2004
Location: Riverside, California
Posts: 2,804
Thanks: 1
Thanked 0 Times in 0 Posts
|
Re: lowering/ tire wear question
^^No, it won't be that bad. I have eibach springs on my GT and it's not super bad once it's been "aligned." It's not perfect in spec of course but the wear isn't excessive.
|
|
11-08-2007, 02:21 PM | #3 | |
AF Enthusiast
Join Date: Jul 2005
Location: San Antonio, Texas
Posts: 2,546
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: lowering/ tire wear question
how much do the adjustable arms cost?
i mean, if theyre cheaper than a pair of tires, it might be worth it... |
|
11-08-2007, 02:57 PM | #4 | |
AF Enthusiast
Join Date: Dec 2004
Location: Rochester, New York
Posts: 1,780
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: lowering/ tire wear question
I have Intrax springs, which drop a bit lower than the eibachs. I don't have the adj. control arms, but I adjusted the rear camber in as close as possible (about a half a degree out of spec). Haven't noticed any abnormal wear yet.
__________________
1997 Mitsubishi 3000GT VR4 - 269AWHP/290AWTQ (Mustang Dyno) - 12.616@106.74 - 1.756 60ft. - 8.06@83.59 (Best TDO4-9B Time) - Driver Mod - IPS TD04-19TL - SPEC 4+ - Wiseco Pistons - 3SX Custom Forged Rods - PMP FMIC + Much More. |
|
11-08-2007, 04:38 PM | #5 | |
AF Regular
Thread starter
Join Date: Sep 2007
Location: Pasadena, Texas
Posts: 131
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: lowering/ tire wear question
cool so just as long as the aligment is just a few hairs off with the lowering springs.... i should be ok then right.... & for blink the adjustable arms run for 400 at 3sx
__________________
97 3kgt sohc.... intake, custom exhaust, 3sx crank pulley, JVC head unit, pioneer speakers all around for highs and mids amped, 12"JBL power series sub.... |
|
11-08-2007, 05:38 PM | #6 | ||
AF Enthusiast
Join Date: Jul 2005
Location: San Antonio, Texas
Posts: 2,546
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: lowering/ tire wear question
Quote:
|
||
11-08-2007, 06:04 PM | #7 | |
Your worst nightmare
Join Date: Oct 2004
Location: Smithfield, Pennsylvania
Posts: 6,058
Thanks: 40
Thanked 252 Times in 246 Posts
|
Re: lowering/ tire wear question
NA's with only springs usually dont need the control arms.
__________________
|
|
|
POST REPLY TO THIS THREAD |
|
|