249 Access cover
BillD
08-31-2004, 05:49 PM
CRAP! Trying to get the access cover off of my 249 transfer case and can't budge the two torx screws. Any Ideas? I want to swap in a new VC
without pulling the TC.
without pulling the TC.
JDPascal
08-31-2004, 06:17 PM
Try heating the heads of the torx screws with a propane or butane torch.
Make sure that the area is free of grease and oil and all wiring harnesses are well clear.
consentrate the heat on the head of the bolt as much as possible and try and move it while it is hot.
Once it moves and loosens a little, I let it cool some and then complete the removal. Just keeps me from burning my fingers thats all.
JD
Make sure that the area is free of grease and oil and all wiring harnesses are well clear.
consentrate the heat on the head of the bolt as much as possible and try and move it while it is hot.
Once it moves and loosens a little, I let it cool some and then complete the removal. Just keeps me from burning my fingers thats all.
JD
BillD
08-31-2004, 09:02 PM
Thanx, JD, I'll give it a shot after I get another torx
socket. Snapped two so far. I was just about ready to take the cold chisel to the dang thing.
BD
socket. Snapped two so far. I was just about ready to take the cold chisel to the dang thing.
BD
BillD
09-01-2004, 05:19 PM
JD: Heat was the trick. The screws let go easily after I heated them. I used a bernzomatic butane pencil torch. Its only 5 inches long and about as round as a "c" cell battery. Worked nicely in that tight spot.
We operate on the patient tomorrow. Mooh ha ha! :ylsuper:
BD
We operate on the patient tomorrow. Mooh ha ha! :ylsuper:
BD
Cam7
09-02-2004, 04:16 AM
JD: Heat was the trick. The screws let go easily after I heated them. I used a bernzomatic butane pencil torch. Its only 5 inches long and about as round as a "c" cell battery. Worked nicely in that tight spot.
We operate on the patient tomorrow. Mooh ha ha! :ylsuper:
BD
How much did you pay for the VC?
We operate on the patient tomorrow. Mooh ha ha! :ylsuper:
BD
How much did you pay for the VC?
msrjeep
09-02-2004, 10:01 AM
red locktite thread locker needs to be broken with heat, about 300F. i would put some back on when you put it back together.
BillD
09-03-2004, 07:41 AM
Cam: $400+$20 shipping. Got on Ebay. It is supposedly the latest version with updated fluid .
msr: They used some kind of thread lock for sure! It was some kind of white hard stuff. The wire wheel cleaned the threads nicely but had to use a little effort. Tough stuff!
BD
msr: They used some kind of thread lock for sure! It was some kind of white hard stuff. The wire wheel cleaned the threads nicely but had to use a little effort. Tough stuff!
BD
Cam7
09-04-2004, 12:05 AM
Cam: $400+$20 shipping. Got on Ebay. It is supposedly the latest version with updated fluid .
msr: They used some kind of thread lock for sure! It was some kind of white hard stuff. The wire wheel cleaned the threads nicely but had to use a little effort. Tough stuff!
BD
Thanks, Ive seen them Listed there before. Just got both of my Half Shafts for my GC on E-bay. Thanks again.
msr: They used some kind of thread lock for sure! It was some kind of white hard stuff. The wire wheel cleaned the threads nicely but had to use a little effort. Tough stuff!
BD
Thanks, Ive seen them Listed there before. Just got both of my Half Shafts for my GC on E-bay. Thanks again.
Automotive Network, Inc., Copyright ©2026